University of Minnesota
University of Minnesota: Department of Mechanical Engineering
http://www.me.umn.edu/

Terry Simon Publications

Archival Publications

1. Jako, C., N. Hower and T. Simon. 1979. "Installation and Thermal Design of Synchrotron Radiation Beam Ports at SPEAR," IEEE Transactions on Nuclear Science, Vol. NS-26, No. 3, pp. 1-3.

2. Simon, T. W. and R. J. Moffat. 1983. "Turbulent Boundary Layer Heat Transfer Experiments--A Separate Effects Study on a Convexly-Curved Wall," J. Heat Transfer, Vol. 105, No. 4, pp. 835-840.

3. Simon T. W., and R. J. Moffat. 1982. "Convex Curvature Effects on the Heated Turbulent Boundary Layer," Proceedings of the VIIth Int. Heat Trans. Conf., Vol. 3, pp. 295-301.

4. Leslie, B., A. Nukermans , T. W. Simon and J. Foster. 1983. "Enhanced Brightness X-Ray Source," J. Vac. Sci. Tech., B1 (4), pp. 1251-1256.

5. Wang, T., T. W. Simon and J. Buddhavarapu. 1985. "Heat Transfer and Fluid Mechanics Measurements in Transitional Boundary Layer Flows," J. Engr. for Gas Turbines and Power, Vol. 107, No. 4, pp. 1007-1015.

6. Wang T., and T. W. Simon. 1987. "Heat Transfer and Fluid Mechanics Measurements in a Boundary Layer Undergoing Transition on a Convex-Curved Wall," ASME J. Turbomachinery, Vol. 109, No. 3, pp. 443-452.

7. Bar-Cohen A., and T. W. Simon. 1988. "Wall Superheat Excursions in the Boiling Incipience of Dielectric Fluids," Heat Transfer Engineering, Vol. 9, No. 3, pp. 19-31.

8. Samant K. R., and T. W. Simon. 1989. "Heat Transfer from a Small, High-Heat Flux Patch to a Subcooled Turbulent Flow," J. Heat Transfer, Vol. 111, No. 4, pp. 1053-1059.

9. You, S. M., T. W. Simon and J. Kim. 1986. "Boundary Layer Heat Transfer and Fluid Mechanics Measurements on a Mildly-Curved Convex Wall," Proc. of the Eighth International Heat Transfer Conference, Vol. 3, pp. 1089-1094.

10. You, S. M., T. W. Simon and J. Kim. 1989. "Free-stream Turbulence Effects on Convex-curved Turbulent Boundary Layers," ASME J. Heat Transfer, Vol. 111, No. 1, pp. 66-72.

11. Kim, J., and T. W. Simon. 1988. "Measurements of the Turbulent Transport of Heat and Momentum in Convexly Curved Boundary Layers: Effects of Curvature, Recovery and Free-Stream Turbulence," J. Turbomachinery, Vol. 110, No. 1, pp. 80-87.

12. Lee, T. Y., T. W. Simon and A. Bar-Cohen. 1988. "An Investigation of the Short-Heating-Length Effect on Forced Convection Critical Heat Flux in a Subcooled Turbulent Flow," Cooling Technology for Electronic Equipment, W. Aung, ed., Hemisphere, pp. 435-450.

13. Wang, T., and T. W. Simon. 1989. "Development of a Special-Purpose Test Surface Guided by Uncertainty Analysis: Introduction of a New Uncertainty Analysis Step," AIAA J. of Thermophysics and Heat Transfer, Vol. 3, No. 1, pp. 19-26.

14. Saylor, J. R., A. Bar-Cohen, T. Y. Lee, T. W. Simon, W. Tong, P. S. Wu. 1988. "Fluid Selection and Property Effects on Single and Two-Phase Immersion Cooling," IEEE Transactions of the Components, Hybrids and Manufacturing Technology Society, Vol. 11, No. 4, pp. 557-565.

15. You, S. M., T. W. Simon, A. Bar-Cohen and W. Tong. 1990. "Experimental Investigation of Nucleate Boiling Incipience with a Highly Wetting Dielectric Fluid (R-113),” International Journal of Heat and Mass Transfer, Vol. 33, No. 1, pp. 105-117.

16. Tong, W., A. Bar-Cohen, T. W. Simon, and S. M. You. 1990. "Contact Angle Effects on Boiling Incipience of Highly-Wetting Liquids," International Journal of Heat and Mass Transfer, Vol. 33, No. 1, pp. 91-103.

17. You, S. M., T. W. Simon and A. Bar-Cohen. 1990. "Experiments on Boiling Incipience with a Highly-wetting Dielectric Fluid: Effects of Pressure, Subcooling and Dissolved Gas Content," Proc. Ninth International Heat Transfer Conference, Vol. 2, pp. 337-342, Jerusalem, Israel.

18. Tong, W., A. Bar-Cohen and T. W. Simon. 1990. "Thermal Transport Mechanisms in Nucleate Pool Boiling of Highly-Wetting Liquids," Proc. Ninth International Heat Transfer Conference, Vol. 2, pp. 27-32, Jerusalem, Israel.

19. You, S. M., A. Bar-Cohen and T. W. Simon. 1990. "Boiling Incipience and Nucleate Boiling Heat Transfer of Highly-Wetting Dielectric Fluids from Electronic Materials," IEEE Transactions on Components, Hybrids and Manufacturing Technology, Vol. 13, No. 4, pp. 1032-1039.

20. Kim, J., T. W. Simon and M. Kestoras. 1994. "Fluid Mechanics and Heat Transfer Measurements in Transitional Boundary Layers Conditionally Sampled on Intermittency," ASME Journal of Turbomachinery, Vol. 116, No. 3, pp. 405-416.

21 Kim, J., T. W. Simon and S. G. Russ. 1992. "Free-Stream Turbulence and Concave Curvature Effects on Heated, Transitional Boundary Layers," Journal of Heat Transfer, Vol. 114, pp. 338-347.

22. Salce, A., and T. W. Simon. 1991. "Investigation of the Effect of Flow Swirl on Heat Transfer Inside a Cylindrical Cavity," Journal of Heat Transfer, Vol. 113, No. 2, pp. 348-354.

23 Russ, S., and T. W. Simon. 1991. "On the Rotating, Slanted, Hot-wire Technique," Experiments in Fluids, Vol. 12, pp. 76-80.

24 Bar-Cohen, A., W. Tong and T. W. Simon. 1992. "Theoretical Aspects of Nucleate Pool Boiling with Dielectric Liquids," Journal of Thermal Science (China), Vol. 1, No. 1.

25 You, S. M., T. W. Simon and A. Bar-Cohen. 1992. "A Technique for Enhancing Boiling Heat Transfer with Application to Cooling of Electronic Equipment," IEEE Transactions on Components, Hybrids and Manufacturing Technology Trans., Vol. 15, No. 5, pp. 823-831.

26. Kestoras, M. D., and T. W. Simon. 1992. "Hydrodynamic and Thermal Measurements in a Turbulent Boundary Layer Recovering from Concave Curvature," ASME Journal of Turbomachinery, Vol. 114, No. 4, pp. 891-898.

27 Wu, P. S., and T. W. Simon. 1994. "Critical Heat Flux and Subcooled Flow Boiling with Small Heated Regions on Straight and Concave-Curved Walls," Proc. of the 10th Int'l Heat Transfer Conf., Vol 7, pp. 569-574, G. F. Hewitt, Ed.

28 You, S. M., T. W. Simon, A. Bar-Cohen and Y. S. Hong. 1995. "Effects of Dissolved Gas Content in Pool Boiling of a Highly-wetting Fluid," J. Heat Transfer, Vol. 117, No. 3, pp. 687-692.

29 Volino, R. J., and T. W. Simon, 1994. "An Application of Octant Analysis to Turbulent and Transitional Flow Data," Journal of Turbomachinery, Vol. 116, No. 4, pp. 752-758.

30 Ibrahim, M., C. Baur, T. Simon and S. Qiu. 1994. "Modeling of Oscillatory Laminar, Transitional, and Turbulent Channel Flows and Heat Transfer," Proc. of the 10th Int'l. Heat Transfer Conf., Vol. 4, pp. 247-252, G. F. Hewitt, Ed.

31. Kestoras, M. D., and T. W. Simon. 1995. "Effects of Free-Stream Turbulence Intensity on a Boundary Layer Recovering from Concave Curvature Effects," Journal of Turbomachinery, Vol. 117, No. 2, pp. 240-247.

32 Kestoras, M. D., and T. W. Simon. 1996. "Turbulence Measurements in a Heated Concave Boundary Layer under High Free-Stream Turbulence Conditions," ASME Journal of Turbomachinery, Vol. 118, No. 1, pp. 172-180.

33 Volino, R. J.. and T. W. Simon. 1995. "Bypass Transition in Boundary Layers Including Curvature and Favorable Pressure Gradient Effects," ASME J. of Turbomachinery, Vol. 117, No. 1, pp. 166-174.

34. Volino, R. J., and T. W. Simon. 1997. "Boundary Layer Transition under High Free-Stream Turbulence and Strong Acceleration Conditions: Part 1, Mean Flow Results," ASME J. of Heat Transfer, Vol. 119, No. 3, pp. 420-426.

35. Volino, R. J., and T. W. Simon. 1997. "Boundary Layer Transition under High Free-Stream Turbulence and Strong Acceleration Conditions: Part 2, Turbulent Transport Results," ASME J. of Heat Transfer, Vol. 119, No. 3, pp. 427-432.

36. Volino, R. J., and T. W. Simon. 1995. "Measurements of Turbulent Transport in Transitional Boundary Layers under High Free-Stream Turbulence and Strong Acceleration Conditions," Proc. of the Tenth Symposium on Turbulent Shear Flows, University Park, PA.

37 You, S. M., T. W. Simon and A. Bar-Cohen. 1997. "Pool Boiling Heat Transfer with an Array of Flush-Mounted, Square Heaters on a Vertical Surface," ASME Journal of Electronic Packaging, Vol. 119, pp. 17-25.

38. Volino, R. J., and T. W. Simon. 1997. "Measurements in a Transitional Boundary Layer with Görtler Vortices," ASME J. of Fluids Engr., Vol. 119, pp. 562-568.

39. Volino, R. J., and T. W. Simon. 1997. "Velocity and Temperature Profiles in Turbulent Boundary Layer Flows Experiencing Streamwise Pressure Gradients," J. Heat Transfer, Vol. 119, No. 3, pp. 433-439.

40. Kestoras, M. D., and T. W. Simon. 1997. "Turbulent Transport Measurements in a Heated Boundary Layer: Combined Effects of Free-Stream Turbulence and Removal of Concave Curvature," ASME J. Heat Transfer , Vol. 119, No. 3, pp. 413-419.

41. Burd, S. W. and Simon, T. W. 1999. Measurements of Discharge Coefficients in Film Cooling, ASME J. of Turbomachinery, Vol. 121, No. 2, pp. 243-248.

42. Burd, S. W. and Simon, T. W. 1999. Turbulence Spectra and Length Scales Measured in Film Coolant Flows Emerging from Discrete Holes, ASME J. of Turbo., Vol. 121, pp. 551-557.

43. Kestoras, M. D. and Simon, T. W. 1998. "Conditionally Sampled Measurements in a Heated Turbulent Boundary Layer: Curvature and Free-Stream Turbulence Effects," Exp. Thermal and Fluid Science, Vol. 17 pp. 63-70, Elsevier Science Publishers.

44. Kaszeta, R. W. and Simon, T. W. 1999. “Measurement of Eddy Diffusivity of Momentum in Film Cooling Flows with Streamwise Injection, ASME J. of Turbomachinery, Vol. 122, pp 178-183.

45. Burd, S., Kaszeta, R. W., and Simon, T. W. 1998. Measurements in Film Cooling Flows: Hole L/D and Turbulence Intensity Effects," ASME J. of Turbomachinery, Vol. 120, pp 791-798.

46. Volino, R. J., and Simon, T. W., 2000. Spectral Measurements in Transitional Boundary Layers on a Concave Surface under High and Low Free-Stream Turbulence Conditions,” ASME Journal of Turbomachinery, Vol. 122, pp. 450-457.

47. Eckert, E. R. G., Sakamoto, H. and Simon, T. W., 2001, “The Heat/Mass Transfer Analogy Factor, Nu/Sh, for Boundary Layers on Turbine Blade Profiles,” International Journal of Heat and Mass Transfer, Vol. 44, No. 6, pp. 1223-1233.

48. Burd, S. W. and Simon, T. W., “Flow Measurements in a Nozzle Guide Vane Passage with a Low Aspect Ratio and Endwall Contouring,” ASME J. Turbomachinery, Vol. 122, pp. 659-666. October 2000.

49. A. R. Byerley, O. Stormer, J. W. Baughn, T. W. Simon and K. W. VanTreuren, 2002, “A ‘Cool' Thermal Tuft for Detecting Surface Flow Direction,” ASME J. of Heat Transfer Photo Gallery, Vol. 124, p. 594.

50. A. R. Byerley, O. Stormer, J. W. Baughn, T. W. Simon, K. W. VanTreuren and J. List, 2003, “Using Gurney Flaps to Control Laminar Separation of Linear Cascade Blades,” ASME Journal of Turbomachinery, Vol. 125, No. 1, pp. 114-120.

51. K. W. Van Treuren, T. W. Simon, M. Von Koller, A. R. Byerley, R. Rivir and J. W. Baughn, 2002, “Measurements in a Turbine Cascade Flow under Ultra Low Reynolds Number Conditions,” ASME Journal of Turbomachinery, Vol. 124, pp. 100-106, 2002.

52. Kaszeta, R. W., Simon, T. W., Jiang, N. And Ottaviani, F., 2005, “The Influence of Wake Passing Frequency and Elevated Turbulence Intensity on Transition,” accepted for the AIAA Journal of Thermophysics, Vol. 19 No. 2, pp. 137-147.

53 Jiang, N. and Simon, T. W., 2005 “Transition in Low-Pressure Turbines: Effects of Unsteady Acceleration and Turbulence Intensity,” AIAA J. of Thermophysics, Vol. 19, No. 2, pp. 148-155.

54 Niu, Y., Simon, T. W., Gedeon, D. and Ibrahim, M. B., “Direct Measurements of Eddy Transport and Thermal Dispersion in a High-Porosity Matrix,” AIAA J. of Thermophysics Vol. 20, No. 1, Jan-March, 2006, pp. 101-106

55. Simon, T. W. and Piggush, J. D., “Turbine Endwall Aerodynamics and Heat Transfer,” AIAA Journal of Propulsion and Power, vol. 22, No. 2, March-April 2006, pp. 301-312.

56. Piggush, J. D. and Simon, T. W., 2006. “Heat Transfer Measurements in a First Stage Nozzle Cascade having Endwall Contouring: Misalignment and Leakage Studies,” J. of Turbomachinery, vol. 129, no. 4, October 2007, pp. 782-790.

57. Piggush, J. D. and Simon, T. W., 2007, “Measurements of Net Change in Heat Flux as a Result of Leakage and Steps on the Contoured Endwall of a Gas Turbine First Stage Nozzle,” Applied Thermal Engineering, Vol. 27, pp. 722–730.

58. Simon, T. W., and N. Jiang, 2009, “Transition of Boundary Layer Flows with Application to Turbomachinery Airfoils,” Journal of Enhanced Heat Transfer, Vol. 16, No. 3, pp. 205-223.

59. Ibrahim, M. B., D. Danila, T. W. Simon, D. Gedeon, and R. Tew, 2009, “Computational Modeling of a Segmented-Involute-Foil Regenerator for Stirling Engines,” Journal of Thermophysics and Heat Transfer, Vol. 23, No. 4, pp. 786-800.

60. Alshare, A. A., T. W. Simon, and P. J. Strykowski, 2010, “Simulations of Flow and Heat Transfer in a Serpentine Heat Exchanger having Dispersed Resistance with Porous-continuum and Continuum models,” International Journal of Heat and Mass Transfer, Vol. 53, pp. 1088-1099.

61. Alshare, A. A., P. J. Strykowski, and T. W. Simon, 2010, “Modeling of Unsteady and Steady Fluid Flow, Heat Transfer and Dispersion in Porous Media using Unit Cell Scale,” International Journal of Heat and Mass Transfer, Vol. 53, pp. 2294-2310.

62. Erickson, R. and Simon, T., 2011, “Effects of Stator/Rotor Leakage Flow and Axisymmetric Contouring on Endwall Adiabatic Effectiveness and Aerodynamic Loss,” Heat Transfer Research, Begell-House Press, Vol. 42, No. 1, pp. 45-64.

63. Zhu, X., Simon, T. W. , and Cui, T., 2011, “Hot Embossing at Viscous State to Enhance Filling Process for Complex Polymer Structures,” Microsyst. Technol., Dec. 2011, DOI 10.1007/s00542- 011-1389-5

64. Taiho Yeom, Min Zhang, Terrence W. Simon, and Tianhong Cui, 2012, “High-Frequency, Large-Displacement, and Low-Power-Consumption Piezoelectric Translational Actuators Based on an Oval Loop Shell,” Sensors and Actuators A: Physical, 176 (2012) 99– 109.

65. Taiho Yeom, Terrence W. Simon, Mark T. North, and Tianhong Cui, 2012, “Piezoelectric Translational Agitation for Enhancing Heat Transfer of a Channel Wall as an Electronics Cooling Mechanism,” IJHMT, Vol. 55, p. 7398-7409 (2012)

66. Piggush, J. D., and T. W. Simon, 2013, “Flow Measurements in a First Stage Nozzle Cascade having Endwall Contouring, Leakage, and Assembly Features,” ASME J. of Turbomachinery DOI 10.1115/1.4006419.

67. Yu, Y., Simon, T.W., and Cui, T., 2013, “A Parametric Study of Heat Transfer in an Air-Cooled Heat Sink Enhanced by Actuated Plates,” Intl. J. of Heat and Mass Transfer, 64, pp. 792-801.

68. Yu, Y., Simon, T.W., Zhang, M., Yeom, T., North, M., and Cui, T., 2014 “Enhancing Heat Transfer in Air-Cooled Heat Sinks Using Piezoelectrically-Driven Agitators and Synthetic Jets,” IJHMT, 68, pp. 184-193.

69. Zhang, C., Yan, B., Wieberdink, J., Li, P.Y., Van de Ven, J., Loth, E. and Simon, T. W., 2014, Thermal Analysis of a Compressor for Application to Compressed Air Energy Storage,” Applied Thermal Engineering, Volume 73, Issue 2, 22 December 2014, Pages 1402–1411.

70. Qin, C., Loth, E., Li, P., Simon, T., and Van De Ven, J., 2014, “Spray-Cooling Concept for Wind-Based Compressed Air Energy Storage,” Journal of Renewable and Sustainable Energy, Vol. 6, 043125, DOI:1.1063/1.4893434

71. Reich, L., Bader, R., Simon, T., Lipinski, W., “Thermal Transport Model of a Packed-bed Reactor for Solar Thermochemical CO2 Capture,” Special Topics & Reviews in Porous Media — An International Journal, 6 (2): 197–209 (2015).

72. Zhang, C. Simon, T. W. Li, P. Y., and Van de Ven, J., 2015 “Numerical Modeling of Three Dimensional Heat Transfer and fluid Flow through Interrupted Plates using Unit Cell Scale,” Journal of Special Topics and Reviews, Special Topics & Reviews in Porous Media — An International Journal, 6 (2): 145–158 DOI:10.1615/.2015012321 (2015)

73. Yeom, T., Simon, T., Zhang, M., North, M., and Cui, T., “High Frequency, Large Displacement and Low Power Consumption Piezoelectric Translational Actuator Based on an Oval Sloop Shell,” Sensors and Actuators A: Physical, Volume 176, 2014, pp. 99-109

74. Guo, S-P., Wu, Z., Kukulka, D., Li, W., Sunden, B., Zhou, X-P., Wei, J-J., and Simon T., 2015, “Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth, Herringbone and Enhanced Surface EHT Tubes, International Journal of Heat and Mass Transfer Volume 85, Pages 281–291.

75. Agrawal, S., Simon, T., North, M., Bissell, D., and Cui, T., 2015, “Heat Transfer Augmentation of a Channel Flow by Active Agitation and Surface Mounted Cylindrical Pin Fins,” International Journal of Heat and Mass Transfer, Volume 87, Pages 557–567.

76. Liu, J., Xie, G. and Simon, T., 2015, “Turbulent Flow and Heat Transfer Enhancement in Rectangular Channels with Novel Cylindrical Grooves,” International Journal of Heat and Mass Transfer, Vol. 81, pp. 563-577.

77. Agrawal, S., Simon, T., North, M., and Cui, T., 2015, “An Experimental Study on the Effects of Agitation on Convective Heat Transfer,” International Journal of Heat and Mass Transfer, Volume 90, November, Pages 302–313

78. Yan, B., Wieberdink, J., Shirazi, F., Li, P., Simon, T., and Van de Ven, J., 2015, “Experimental Study of Heat Transfer Enhancement in a Liquid Piston Compressor/Expander for Compressed Air Energy Storage using Porous Inserts,” Applied Energy, v. 154, pp. 40-50, 2015.

79. Yeom, T., Simon, T., Zhang, T., Zhang, M., North, M., and Cui, T., 2016, “Enhanced heat transfer of heat sink channels with micro pin fin roughened walls,” International Journal of Heat and Mass Transfer, v. 92, pp. 617–627.

80. Reich, L., Melmoth, L., Bader, R., Gresham, R., Simon, T., and Lipinski. W., 2017, “A solar reactor design for research on calcium oxide-based carbon-dioxide capture,” Technical brief SOL-15-1106, (accepted for the ASME JSEE)

81. Yeom, T., Simon, T., North, M., and Cui, T., “High-Frequency Translational Agitation with Micro Pin-Fin Surfaces for Enhancing Heat Transfer of Forced Convection,” International Journal of Heat and Mass Transfer 94 (2016) 354–365.

82. Reich, L., Melmoth, L., Bader, R., Gresham, R., Simon, T., Lipinski, W., “A Solar Thermochemical Reactor Design for Research on Calcium Oxide-Based Carbon Dioxide Capture,” SOL-15-1106, Technical Brief to the ASME Journal of Solar Energy, DOI: 10.1115/1.4037089.

83. Zhang, C., Li, P., Van de Ven, Simon, T., 2016 “Design Analysis of a Liquid-Piston Compression Chamber with Application to Compressed Air Energy Storage,” Applied Thermal Engineering  (2016), pp. 704-709 DOI information: 10.1016/j.applthermaleng.2016.01.082

84. Liu, Z., Li, J., Feng, Z., and Simon, T., 2015, “Numerical Study on the Effect of Jet Nozzle Aspect Ratio and Jet Angle on Swirl Cooling in a Model of a Turbine Blade Leading Edge Cooling Passage, IJHMT 90 (2015) 986–1000.

85. Yue, L., Reich, L., Simon, T., Bader, R., and Lipinski, W., 2016, “Progress in Thermal Transport Modeling of Carbonate-based Reacting Systems,” NHT2015 Special Issue of the International Journal of Numerical Methods for Heat and Fluid Flow (accepted for publication)

86. Li, W., Chen, X., Chen, J-H., Sun, Sun, Z-C., and Simon, T, 2016, Shell-Side Flow Condensation of R410A on Horizontal Tubes at Low-Mass Fluxes, J. Heat Transfer, DOI: 10.1115/1.4034552

87. Liu, Z., Li, J., Feng, Z. and Simon, T., 2016, Numerical study on the effect of jet spacing on the Swirl flow and heat transfer in the turbine airfoil leading edge region, Numerical Heat Transfer, Part A: Applications, 10.1080/10407782.2016.1230381

88. Yang, C., Simon, T. and Cui, T., 2017, Numerical simulation and analysis of hybrid physical-chemical vapor deposition of perovskite MAPbI3, Journal of Applied Physics 121, 144903 doi: 10.1063/1.4980116, http://dx.doi.org/10.1063/1.4980116

89. Yue, L., Reich L., Simon, T., Bader, R. and Lipinski, W., 2016, Progress in thermal transport modeling of carbonate-based reacting systems, Volume 27 Issue 5 International Journal of Numerical Methods for Heat & Fluid Flow

 

Invited Papers

1. Simon, T. W. 1981. "Data Evaluation: Boundary Layer Flows with Streamwise Curvature" Proceedings of the 1980 AFOSR-HTTM Stanford Conference on Complex Turbulent Flows, Vol. I, pp. 99-110, Thermosciences Div., Mech. Engr. Dept., Stanford University.

2. Simon, T. W., and J. Seume. 1990. "The Stirling Engine; an Engine that Requires High-Flux Heat Exchange under Oscillating Flow Conditions," Invited paper for the A. L. London Symposium, Stanford University, March, 1989, published in Compact Heat Exchangers A Festschrift for A. L. London, Hemisphere Publishing Corporation, New York.

3. Simon, T. W. 1991. "Forced Convection Boiling on Small Regions," Proc. of the 3rd ASME/JSME Thermal Engineering Joint Conference, ASME Vol. 2, pp. 259-268.

4. Simon, T. W., and P-S Wu. 1993. "Flow Boiling Critical Heat Flux on Small Heated Regions," High Heat Flux Engineering II, Proc. of the High Heat Flux Engineering Symposium at the 1993 International Symposium on Optical Applied Science and Engineering, San Diego, CA, 11-16 July, 1993.

5. Simon, T. W. and R. Oke, 1998, Heat Transfer and Flow Measurements in Gas Turbine Film Cooling, Proceedings of the Energy Sources Technology Conference and Exhibition (ETCE'98) Paper # 4715, Houston, TX, February 1998.

6. Simon, T. W., S. W. Burd, C. J. Satterness, R. W Kaszeta, and R. Oke, 1999, “Documenting Complex flows in Gas Turbine Gas Path Cooling Systems,” Proc. Colloquium on Turbomachinery - 1999, S. J. Song, Ed., Turbo and Power Machinery Research Center, Seoul National University, Seoul Korea, pp. 1-16.

7. Simon T. W., and R. W. Kaszeta, “Transition to Turbulence Under Low-Pressure Turbine Conditions,” Turbine 2000 Workshop, Proceedings of the International Symposium on Heat Transfer in Gas Turbine Systems, Cesme, Turkey, 13-18 August 2000, Annals of the New York Academy of Sciences, Vol. 934.

8. Srinivasan, V., T. W. Simon, and R. J. Goldstein, “Synopsis: Technical Issues Covered in Turbine 2000,” Turbine 2000 Workshop, Proceedings of the International Symposium on Heat Transfer in Gas Turbine Systems, Cesme, Turkey, 13-18 August 2000, Annals of the New York Academy of Sciences, Vol. 934.

9. Simon, T. W., 2001, “The Changing Electric Power Scene in the U.S.: Implications for Microturbines, Fuel Cells and other Distributed Power Systems,” presented at the Core Research for Evolutional Science and Technology (CREST) Public Conference on Research Achievements, Kyoto University, sponsored by Japan Science and Technology Corporation, Research Director, Kenjiro Suzuki.

10. Simon, T. W. and N. Jiang, 2002 “Development and Applications of Microturbines,” International Symposium on Distributed Energy Systems in the 21st Century, September 24-25, Tokyo Japan.

11. Simon, T. W. and N. Jiang, 2003, “Micro- or Small-Gas Turbines, Keynote address and paper, JSME Japan International Gas Turbine Conference, November, 2003.

12. Simon, T. W. and J. D. Piggush, 2006, “Turbine Endwall Aerodynamics and Heat Transfer,” 2006, Invited paper for the Special Section on Turbine Reliability in the AIAA Journal of Propulsion and Power, Volume 22, No. 2, Journal of Propulsion and Power (March-April 2006), (same as A-55).

13. Simon, T. W., and N. Jiang, 2007, “Transition of Boundary Layer Flows with Application to Turbomachinery Airfoils,” 19th National and 8th ISHMT-ASME Heat and Mass Transfer Conference, January 3-5, 2008, JNTU Hyderabad, India.

14. Zhang, C., Yan, B., Wieberdink, J., Li, P., Van de Ven, J., and Simon, T., 2013, ”Thermal Analysis of a Compressor for Application to Compressed Air Energy Storage,” IWHT2013-001, Proceedings of IWHT2013 2nd International Workshop on Heat Transfer Advances for Energy Conservation and Pollution Control October 18-21, 2013, Xi’an, China

15. Yue, L., Reich, L., Simon, T., Bader, R. and Lipinski, W., 2017, Progress in thermal transport modeling of carbonate-based reacting systems., International Journal of Numerical Methods for Heat and Fluid Flow, in press. Invited paper.

Journal Review Articles

1. Eckert, E. R. G., R. J. Goldstein, S. V. Patankar, E. Pfender, J. W. Ramsey, T. W. Simon, E. M. Sparrow and K. Y. Teichman. 1981. "Heat Transfer--A Review of 1980 Literature," Int. J. Heat Mass Transfer, Vol. 24, No. 12, pp. 1863-902.

2. Eckert, E. R. G., R. J. Goldstein, S. V. Patankar, E. Pfender, J. W. Ramsey, T. W. Simon and E. M. Sparrow. 1982. "Heat Transfer--A Review of 1981 Literature," Int. J. Heat Mass Transfer, Vol. 25, No. 12, pp. 1783-1812.

3. Eckert, E. R. G., R. J. Goldstein, E. Pfender, W. E. Ibele, S. V. Patankar, J. W. Ramsey, T. W. Simon and N. A. Decker. 1983. "Heat Transfer--A Review of 1982 Literature," Int. J. Heat Mass Transfer, Vol. 26, No. 12, pp. 1733-1770.

4. Eckert, E. R. G., R. J. Goldstein, S. V. Patankar, E. Pfender, J. W. Ramsey, T. W. Simon, N. Decker and T. H. Kuehn. 1984. "Heat Transfer--A Review of the 1983 Literature," Int. J. Heat Mass Transfer, Vol. 27, No. 12, pp. 2179-2214.

5. Eckert, E. R. G., R. J. Goldstein, S. V. Patankar, E. Pfender, J. W. Ramsey, T. W. Simon, N. Decker, T. H. Kuehn and H. Lee. 1985. "Heat Transfer--A Review of the 1984 Literature," Int. J. Heat Mass Transfer, Vol. 28, No. 12, pp. 2181-2227.

6. Eckert, E. R. G., R. J. Goldstein, E. Pfender, W. E. Ibele, J. W. Ramsey, T. W. Simon, N. A. Decker, T. H. Kuehn, H. O. Lee and S. L. Girshick. 1986. "Heat Transfer--A Review of the 1985 Literature," Int. J. Heat Mass Transfer, Vol. 29, No. 12, pp. 1767-1841.

7. Eckert, E. R. G., R. J. Goldstein, E. Pfender, W. E. Ibele, S. V. Patankar, J. W. Ramsey, T. W. Simon, N. A. Decker, T. H. Kuehn, H. O. Lee and S. L. Girshick. 1987. "Heat Transfer -- a review of 1986 literature," Int. J. Heat Mass Transfer, Vol. 30, No. 12, pp. 2449-2553.

8. Eckert, E. R. G., R. J. Goldstein, E. Pfender, W. E. Ibele, S. V. Patankar, J. W. Ramsey, T. W. Simon, N. A. Decker, T. H. Kuehn, H. Lee and S. L. Girshick,. 1988. "Heat Transfer--A Review of 1987 Literature," Int. J. Heat Mass Transfer, Vol. 31, No. 12, pp. 2401-2488.

9. Eckert, E. R. G., R. J. Goldstein, E. Pfender, W. E. Ibele, S. V. Patankar, T. W. Simon, N. A. Decker, H. Lee, S. L. Girshick, C. J. Scott, P. J. Strykowski and K. K. Tamma. 1989. "Heat Transfer--A Review of 1988 Literature," Int. J. Heat Mass Trans., Vol. 32, No. 12, pp. 2211-2280.

10. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, N. A. Decker, H. Lee, S. L. Girshick, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen and J. V. R. Heberlein. 1990. "Heat Transfer--A Review of 1989 Literature," Int. J. Heat Mass Trans., Vol. 33, No. 11, pp. 2349-2437.

11. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, N. A. Decker, S. L. Girshick, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein and D. L. Hofeldt. 1991. "Heat Transfer--A Review of 1990 Literature," Int. J. Heat Mass Trans., Vol. 34, No. 12, pp. 2931-3009.

12. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, S. L. Girshick, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein and D. L. Hofeldt, K. A. Stelson. 1992. "Heat Transfer--A Review of 1991 Literature," International Journal of Heat and Mass Transfer, Vol. 35, No. 12, pp. 3153-3235.

13. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein, D. L. Hofeldt, T. H. Kuehn, and K. A. Stelson. 1994. "Heat Transfer--A Review of 1992 Literature," International Journal of Heat and Mass Transfer, Vol. 37, No. 9, pp. 1285-1373.

14. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, P. J. Strykowski, K. K. Tamma, T. H. Kuehn, A. Bar-Cohen, J. V. R. Heberlein, D. L. Hofeldt, K. A. Stelson, and J. H. Davidson. 1996. "Heat Transfer--A Review of 1993 Literature," International Journal of Heat and Mass Transfer, Vol. 39, No. 5, pp. 885-963.

15. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, P. J. Strykowski, K. K. Tamma, T. H. Kuehn, A. Bar-Cohen, J. V. R. Heberlein, D. L. Hofeldt, J. H. Davidson, J. Bischof and F. Kulacki. 1997. "Heat Transfer--A Review of 1994 Literature," International Journal of Heat and Mass Transfer, Vol. 40, No. 16, pp. 3729-3804.

16. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, P. J. Strykowski, K. K. Tamma, T. H. Kuehn, A. Bar-Cohen, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, and U. Kortshagen. 1999. "Heat Transfer--A Review of 1995 Literature," International Journal of Heat and Mass Transfer, Vol. 42, pp. 2717-2797.

17. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, and U. Kortshagen. 2000. "Heat Transfer--A Review of 1996 Literature," International Journal of Heat and Mass Transfer, Vol. 43, pp. 1273-1371.

18. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, U. Kortshagen and S. Garrick. 2000. "Heat Transfer--A Review of 1997 Literature," International Journal of Heat and Mass Transfer, Vol. 43, pp. 2431-2528.

19. Eckert, E. R. G., R. J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, U. Kortshagen and S. Garrick. 2001. "Heat Transfer--A Review of 1998 Literature," International Journal of Heat and Mass Transfer, Vol. 44, pp. 253-366.

20. Goldstein, R. J., E. R. G. Eckert, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, U. Kortshagen and S. Garrick. 2001. "Heat Transfer--A Review of 1999 Literature," International Journal of Heat and Mass Transfer, Vol. 44, pp. 3579-3699.

21. Goldstein, R. J. , E. R. G. Eckert, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, U. Kortshagen and S. Garrick. 2002. "Heat Transfer--A Review of 2000 Literature," International Journal of Heat and Mass Transfer, Vol. 45, pp. 2853-2957.

22. Goldstein, R. J. , E. R. G. Eckert, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, U. Kortshagen and S. Garrick. 2003. "Heat Transfer--A Review of 2001 Literature," International Journal of Heat and Mass Transfer, Vol. 46, pp. 1887-1992.

23. Goldstein, R. J. , E. R. G. Eckert, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, A. Bar-Cohen, J. V. R. Heberlein J. H. Davidson, J. Bischof, F. Kulacki, U. Kortshagen, S. Garrick and V. Srinivasan. 2005. "Heat Transfer--A Review of 2002 Literature," International Journal of Heat and Mass Transfer, Vol. 48, pp. 819-927.

24. Goldstein, R. J. , W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, J. V. R. Heberlein, J. H. Davidson, J. Bischof, F. A. Kulacki, U. Kortshagen, S. Garrick and V. Srinivasan. 2006. "Heat Transfer--A Review of 2003 Literature," International Journal of Heat and Mass Transfer, Vol. 49, pp. 451-534.

 

Refereed Conference Publications

1. Simon, T. W., and R. J. Moffat. 1979. "Heat Transfer through Turbulent Boundary Layers--The Effects of the Introduction of and Recovery from Convex Curvature," ASME Winter Annual Meeting, ASME 79-WA/GT-10.

2. Simon, T. W., and R. J. Moffat. 1981. "Turbulent Boundary Layer Heat Transfer Experiments--A Separate Effects Study on a Convexly-Curved Wall," 20th Joint ASME/AIChE National Heat Transfer Conference, ASME 81-HT-78, also published in the Journal of Heat Transfer (also a journal publication).

3. Samant, K. R., T. W. Simon, and R. V. Stuart. 1984. "Using Thin-Film Technology to Fabricate a Small-Patch Boiling Heat Transfer Test Section," 22nd ASME-AIChE Nat’l. Heat Transfer Conf., New Experimental Techniques in Heat Transfer--1984, ASME HTD - Vol. 31, pp. 33-38, abstract in Heat Transfer - Niagara Falls 1984, N. M. Farukhi, ed., AIChE Symp. Series 236, Vol. 80.

4. Wang, T., T. W. Simon, and J. Buddhavarapu. 1985. "Heat Transfer and Fluid Mechanics Measurements in Transitional Boundary Layer Flows," 1985 Int’l. Gas Turbine Conf., ASME Paper 85-GT-113, also in the J. of Engr. for Gas Turbines and Power (also a journal publication).

5. Wang, T., and T. W Simon. 1985. "Heat Transfer and Fluid Mechanics Measurements in a Boundary Layer Undergoing Transition on a Convex-Curved Wall," 1985 Nat’l. Heat Transfer Conf., ASME Paper 85-HT-60, also in the J. of Turbomachinery (also a journal publication).

6. Bar-Cohen, A., and T. W. Simon. 1986. "Wall Superheat Excursions in the Boiling Incipience of Dielectric Fluids," 1986 AIAA/ASME Heat Transfer and Thermophysical Conference, also published in Heat Transfer Engineering (also a journal publication).

7. Samant, K. R., and T. W Simon. 1986. "Heat Transfer from a Small, High-Heat Flux Patch to a Subcooled Turbulent Flow," 1986 AIAA/ASME Heat Transfer and Thermophysical Conference, also published in the Journal of Heat Transfer (also a journal publication).

8. Seume, J., and T. W. Simon. 1986. "Oscillating Flow in Stirling Engine Heat Exchangers," 1986 IECEC Conference, Proceedings paper No. 869118, pp. 533-538.

9. You, S. M., T. W. Simon, and J. Kim. 1986. "Free-stream Turbulence Effects on Convex-Curved Turbulent Boundary Layers", 1986 ASME Winter Annual Meeting, ASME Paper 86-WA/HT-46, also published in the Journal of Heat Transfer (also a journal publication).

10. Park, W., and T. W. Simon. 1987. "A Test of the MLH Models for the Prediction of Convex-curved Transitional Boundary Layer Heat Transfer Behavior," 2nd ASME/JSME Joint Thermal Engineering Conference, Proc. Vol. 3, pp. 349-360.

11. Kim, J., and T. W. Simon. 1987. "Measurements of the Turbulent Transport of Heat and Momentum in Convexly Curved Boundary Layers: Effects of Curvature, Recovery and Free-Stream Turbulence," 1987 International Gas Turbine Conference, ASME Paper 87-GT-199, also published in the Journal of Turbomachinery (also a journal publication).

12. Seume, J., T. W. Simon, and L. F. Goldberg. 1987. "Description of the Oscillating Flow Test Program," 1987 IECEC Conference, Proc. 22nd IECEC, paper, #879029, pp. 1753-1758.

13. Seume, J., and T. W. Simon. 1987. "Flow Oscillation Effects in Tubes and Porous Material: Unresolved Issues," 1987 ASME Winter Annual Meeting, HTD-Vol. 93/FED - Vol. 62, pp. 55-62.

14. Wang, T., and T. W Simon. 1988. "Development of a Special-Purpose Test Surface Guided by Uncertainty Analysis: Introduction of a New Uncertainty Analysis Step," 26th AIAA Aerospace Science Meeting, AIAA-88-0169, also published in the AIAA Journal of Thermophysics and Heat Transfer (also a journal publication).

15. Saylor, J. R., A. Bar-Cohen, T. Y. Lee, T. W. Simon, W. Tong, and P. S. Wu. 1988. "Fluid Selection and Property Effects on Single and Two-Phase Immersion Cooling," Intersociety Conf. on Thermal Phenomena in Fabrication and Operation of Electronic Components, also published in the IEEE Transactions of the Components, Hybrids and Manufacturing Tech. (also a journal publication).

16. Seume, J., and T. W. Simon. 1988. "Effect of Transition on Oscillation Flow Losses in Stirling Engine Coolers and Heaters," Proc. 23rd IECEC Conf., New York: ASME, pp. 127-132.

17. Tong, W., T. W. Simon, and A. Bar-Cohen. 1988. "A Bubble Sweeping Heat Transfer Mechanism for Low Heat Flux Boiling on Downward-Facing Inclined Surfaces," 1988 ASME Winter Annual Meeting, ASME HTD-Vol. 104, pp. 173-178.

18. Tong, W., T. W. Simon, and A. Bar-Cohen. 1988. "Effect of Dissolved Gas on Boiling Incipience in Highly-Wetting Liquids," Multi-Phase Transport and Particulate Phenomena (Veziroglu, ed.), Proc. of the Fifth International Symposium on Multi-Phase Transport and Particle Phenomena (Dec. 1988, Miami Florida), Vol. 1, pp. 365-387, Taylor & Francis/Hemisphere Pub., 1990.

19. Saylor, J. R. T. W. Simon, and A. Bar-Cohen. 1989. "The Effect of a Dimensionless Length Scale on the Critical Heat Flux in Saturated, Pool Boiling," 1989 National Heat Transfer Conference, ASME HTD-Vol. 108, Heat Transfer Equipment Fundamentals, Design, Applications and Operating Problems, ed. R. K. Shah, pp. 71-79.

20. Lee, T. Y., and T. W. Simon. 1989. "High-Heat-Flux Forced Convection Boiling from Small Regions," 1989 National Heat Transfer Conference, ASME HTD-Vol. 111, Heat Transfer in Electronics - 1989, ed. R. K. Shah, pp. 7-16.

21. Kim, J., T. W. Simon, and M. Kestoras. 1989. "Fluid Mechanics and Heat Transfer Measurements in Transitional Boundary Layers Conditionally Sampled on Intermittency," 1989 National Heat Transfer Conference, ASME HTD-Vol. 107, Heat Transfer in Convective Flows, ed. R. K. Shah, pp. 69-81, also in Journal of Turbomachinery (also a journal publication)

22. Salce, A., and T. W. Simon. 1989. "Investigation of the Effect of Flow Swirl on Heat Transfer Inside a Cylindrical Cavity," National Heat Transfer Conference, ASME HTD-Vol. 107, Heat Transfer in Convective Flows, ed. R. K. Shah, pp. 177-184, also in the Journal of Heat Transfer (also a journal publication).

23. Lee, T. Y., and T. W. Simon. 1989. "Critical Heat Flux in Forced Convection Boiling from Small Regions," 1989 ASME Winter Annual Meeting, ASME HTD-Vol. 119, Heat Transfer in High Energy/High Heat Flux Applications, ed. R. Goldstein, L. Chow and E. Anderson, pp. 1-8.

24. Tong, W., A. Bar-Cohen, and T. W. Simon. 1989. "Marangoni Flow in Nucleate Boiling" in Some Unanswered Questions in Fluid Mechanics" by L. Trefethen and R. Panton, 1989 Winter Annual Meeting, ASME paper # 89-WA/FE-5, New York.

25. You, S. M., T. W. Simon, and A. Bar-Cohen. 1990. "Experiments on Nucleate Boiling with a Highly-wetting Dielectric Fluid: Effects of Pressure, Subcooling and Dissolved Gas Content," 1990 AIAA/ASME Thermophysics and Heat Transfer Conf., ASME HTD-Vol. 131, Cryogenic and Immersion Cooling of Optics and Elect. Equipment, ed. T. W. Simon and S. Oktay, pp. 45-52.

26. You, S. M., A. Bar-Cohen, and T. W. Simon. 1990. "Boiling Incipience and Nucleate Boiling Heat Transfer of Highly-Wetting Dielectric Fluids from Electronic Materials," 2nd Intersociety Conference on Thermal Phenomena in Electronic Systems (I-THERM-1990), also published in the IEEE Transactions on Components, Hybrids and Manufacturing Technology, Dec. 1990 issue (also a journal publication).

27. Tong, W., A. Bar-Cohen, and T. W. Simon. 1991. "Investigation of Bubble Flow Regimes in Nucleate Boiling of Highly-Wetting Liquids," 3rd ASME/JSME Thermal Engineering Joint Conference, Vol. 2, pp. 433-439.

28. Chung, J. T., and T. W. Simon. 1990. "Three-Dimensional Flow near the Blade/Endwall Junction of a Gas Turbine: Visualization in a Large-Scale Cascade Simulator," ASME Paper # 90-WA/HT-4, 1990 ASME Winter Annual Meeting, Dallas Texas.

29. Friedman, G. T., and T. W. Simon. 1990. "The University of Minnesota Oscillating Flow Experiments," 25th IECEC Conference, Aug. 1990, Reno Nevada, Vol. 5, pp. 393-397, Ed., P. A. Nelson, W. W. Schertz and R. H. Till, Am. Inst. of Chem. Engr., NY.

30. Chung, J. T., and T. W. Simon. 1991. "Three-Dimensional Flow near the Blade/Endwall Junction of a Gas Turbine: Application of a Boundary Layer Fence," ASME 91-GT-45, 36th International Gas Turbine and Aeroengine Congress, Orlando, Florida.

31. You, S M., T. W. Simon, and A. Bar-Cohen. 1991. "Reduced Incipience Superheats in Boiling of Fluids which Hold Dissolved Gas," in Phase Change Heat Transfer - 1991, E. Hensel, V. K. Dhir, R. Grief and J. Fillo, ed. HTD - Vol. 159, pp. 109-117, ASME/AIChE National Heat Transfer Conf., Minneapolis, Minnesota.

32. Kestoras, M. D., and T. W. Simon. 1991. "Hydrodynamic and Thermal Measurements in a Turbulent Boundary Layer Recovering from Concave Curvature," 1991 ASME Winter Annual Meeting, ASME HTD-Vol. 188, Heat Transfer in Gas Turbines - 1991, ed. E. Elovic and H. L. Martin, pp. 29-36, also published in the ASME Journal of Turbomachinery, Vol. 114, No. 4, 1992 (also a journal publication).

33. You, S. M., T. W. Simon and A. Bar-Cohen. 1992. "A Technique for Enhancing Boiling Heat Transfer with Application to Cooling of Electronic Equipment," in I-THERM III the Proceedings of the Third InterSociety Conference on Thermal Phenomena in Electronic Systems, pp. 66-73, IEEE Catalog No. 92-CH3096-5, ITHERM-1992 Conference, also published in IEEE Transactions on Components, Hybrids and Manufacturing Tech. Trans. (also a journal publication).

34. Simon, T. W., and M. F. Blair. 1991. "Boundary Layer Transition with Large External Disturbances" in "Some Unanswered Questions in Fluid Mechanics" by L. Trefethen, R. Panton and J. A. C. Humphrey, 1991 Winter Annual Meeting.

35. You, S. M., T. W. Simon and A. Bar-Cohen. 1992. "Pool Boiling Heat Transfer with an Array of Flush-Mounted, Square Heaters," ASME HTD-Vol. 206-2, Topics in Heat Transfer, Vol. 2, 1992 National Heat Transfer Conference, also published in the ASME Journal of Electronic Packaging, (also a journal publication).

36. Volino, R. J., and T. W. Simon. 1992. "Bypass Transition in Boundary Layers Including Curvature and Favorable Pressure Gradient Effects," ASME HTD-Vol. 226, Fundamental and Applied Heat Transfer Research for Gas Turbine Engines, ed. D. E. Metzger and M. E. Crawford, pp. 51-60, 1992 ASME Winter Annual Meeting, also published in the ASME J. of Turbomachinery (also a journal publication).

37. Qiu, S., and T. W. Simon. 1992. "Visualization of Entry Flow Separation for Oscillating Flow in Tubes," Proc. of the 27th IECEC Conference, Vol. 5, pp. 517- 522, paper # 929465.

38. Simon, T. W., M. Ibrahim, M. Kannaparedy, T. Johnson, and G. Friedman. 1992. "Transition of Oscillatory Flow in Tubes: An Empirical Model for Application to Stirling Engines," Proc. of the 27th IECEC Conference, Vol. 5, pp. 495-502, paper # 929463.

39. Volino, R. J., and T. W. Simon, "An Application of Octant Analysis to Turbulent and Transitional Flow Data," 93-GT-72, Best Heat Transfer Paper Award recipient, 1993 International Gas Turbine Conference, Cincinnati, also published in the Journal of Turbomachinery (also a journal publication).

40. Chung, J. T., and T. W. Simon. 1993. "Effectiveness of the Gas Turbine Endwall Fences in Secondary Flow Control at Elevated Freestream Turbulence Levels," 93-GT-51, 1993 International Gas Turbine Conference, Cincinnati.

41. Kestoras, M. D., and T. W. Simon, "Effects of Free-Stream Turbulence Intensity on a Boundary Layer Recovering from Concave Curvature Effects," 93-GT-25 1993 International Gas Turbine Conference, Cincinnati, also to be published in the Journal of Turbomachinery, 1995 (also a journal publication)

42. Kestoras, M. D., and T. W. Simon. 1993. "Combined Effects of Concave Curvature and High Free-stream Turbulence Intensity on Boundary Layer Heat and Momentum Transport," ASME Paper # 93-WA/HT-56, 1993 ASME Winter Annual Meeting, New Orleans, LA (1993), also published in the Journal of Turbomachinery, 1995.

43. Kestoras, M. D., and T. W. Simon, 1994 "Turbulence Measurements in a Heated, Concave Boundary Layer under High Free-Stream Turbulence Conditions," ASME 94-GT-37, 1994 International Gas Turbine Conference, The Hague, The Netherlands.

44. Wu, P. S., and T. W. Simon. 1994. "Effects of Dissolved Gases on Subcooled Flow Boiling from Small Heated Regions with and without Streamwise Concave Curvature," Proc. of the ITHERM IV Conference, pp. 23-31, IEEE Catalog No. 94CH3340-7.

45. Qiu, S., and T. W. Simon. 1994. "Measurements of Heat Transfer and Fluid Mechanics within an Oscillatory Flow in a Pipe," in Fundamentals of Heat Transfer in Forced Convection 1994, ASME HTD-Vol. 285, pp. 1-8, ed. F. W. Schmidt and R. J. Moffat, Winter Annual Meeting.

46. Volino, R. J., and T. W. Simon. 1994. "Velocity and Temperature Profiles in Turbulent Boundary Layer Flows Experiencing Streamwise Pressure Gradients," in Fundamentals of Heat Transfer in Forced Convection 1994, ASME HDT-Vol. 285, pp. 1-8, ed. F. W. Schmidt and R. J. Moffat, Winter Annual Meeting, (also a journal publication).

47. Kestoras, M. D., and T. W. Simon. 1994. "Turbulent Heat and Momentum Transport Measurements: the Effects of Introduction and Removal of Concave Curvature," in Effects of Organized Vortex Motion on Heat and Mass Transfer, proceedings of EUROMECH Colloquium 327, presented in Kiev, Ukraine.

48. Volino, R. J., and T. W. Simon. 1995. "Boundary Layer Transition under High Free-Stream Turbulence and Strong Acceleration Conditions: Mean Flow Results," Proc. of the 1995 ASME/JSME Thermal Engineering Conference, L. S. Fletcher and T. Aihara, ed., Vol. 1, pp. 335-342, also published in the ASME J. of Heat Transfer (also a journal publication).

49. Volino, R. J., and T. W. Simon. 1994. "Transfer Functions for Turbulence Spectra," Unsteady Flows in Aeropropulsion, ASME AD-Vol. 40, pp. 147-155, 1994 ASME Winter Annual Meeting.

50. Kestoras, M. D., and T. W. Simon. 1995. "Turbulent Transport Measurements in a Heated Boundary Layer: Combined Effects of Free-Stream Turbulence and Removal of Concave Curvature," ASME paper # 95-GT-152, presented at the 1995 International Gas Turbine Conference, Houston, also published in the ASME J. of Heat Transfer (also a journal publication).

51. Desta, G. G., and T. W. Simon. 1995. "Experimental Studies of Boiling Performance in Curved Channels with a Two-Phase Approach Flow," Proc. of the 30th 1995 Nat’l. Heat Trans. Conf. Vol. 12, also ASME HTD-Vol. 314, V. Sernas, R. Boyd and M. Jensen, ed. pp. 125-132.

52. Wu, P. S., and T. W. Simon. 1995. "Subcooled Flow Boiling over a Thin, Low-Capacitance Surface on a Concave Wall," Proc. of the 30th 1995 Nat’l. Heat Trans. Conf. Vol. 12, also ASME HTD-Vol. 314, V. Sernas, R. Boyd and M. Jensen, ed. pp. 177-184.

53. Qiu, S., T. W. Simon, and R. J. Volino , 1995, "Evaluation of Local Wall Temperature, Heat Flux, and Convective Heat Transfer Coefficient from the Near-Wall Temperature Profile, Heat Transfer in Turbulent Flows - 1995, ASME HTD-Vol. 318, N. K. Anand, R. S. Amano and B. F. Armaly, Ed., presented at the ASME-IMECE Conference, San Francisco, CA, 1995, pp. 45-52.

54. Volino, R. J. and T. w. Simon, 1996. "Measurements in a Transitional Boundary Layer with Görtler Vortices", ASME Paper No. 96-GT-166, Presented at the International Gas Turbine Conference, Birmingham, England, also published in J. of Fluid Engr. (also a journal publication).

55. Kestoras, M. D. and Simon, T. W. 1996. "Conditionally Sampled Measurements in a Heated Turbulent Boundary Layer: Curvature and Free-Stream Turbulence Effects," Proc. of the 3rd Int'l. Symp. on Engr. Turbulence Modeling and Measurements, Crete, Greece, Elsevier Science Publishers, also published in Experimental Thermal and Fluid Science (also a journal publication).

56. Wang, L., H. Tsang, T. W. Simon, and E. R. G. Eckert, 1996. Measurements of Mean Flow and Eddy Transport over a Film Cooled Surface," Proc. 31st NHTC, Vol. 5, HTD Vol. 327, R. Mahajan, A. Majumdar, G. Chen, P. Tekriwal, W. Soon, K. Tagavi, P. Phelan, and L. Fletcher, Ed., pp. 71-79.

57. Burd, S., R. W. Kaszeta, and T. W. Simon, 1996. Measurements in Film Cooling Flows: Hole L/D and Turbulence Intensity Effects," ASME Paper # 96-WA/HT-7, presented at the 96-IMECE Conference, Atlanta, GA, also published in the J. of Turbomachinery (also a journal publication).

58. Burd, S. and T. W. Simon, 1997. Influence of Coolant Supply Geometry on Film Coolant Exit Flow and Surface Adiabatic Effectiveness, ASME paper # 97-GT-25 presented at the 97 International Gas Turbine Conference, Orlando Fl.

59. Qiu, S. and Simon, T. W. 1997. An Experimental Investigation of Transition on a Low-Pressure Turbine Airfoil, ASME paper # 97-GT-455, 1997 Int’l Gas Turbine Conf., Orlando Fl.

60. Murawski, C. G., R. S. Sondergaard, R. B. Rivir, K. Vafai, T. W. Simon, and R. Volino, 1997. Experimental Study of the Unsteady Aerodynamics in a Linear Cascade with Low Reynolds Number, Low Pressure Turbine Blades, ASME paper # 97-GT-95, 1997 Intl. Gas Turbine Conf., Orlando Fl.

61. Eckert, E. R. G., T. W. Simon, and B. Graskow, 1997. Exploration of the Influence of Heat Conduction on the Temperature Distribution in Turbine Blades, proceedings of the 1997 NHTC, Baltimore, MD, Vol. 12, ASME HTD-Vol. 350, pp. 199-209.

62. Kaszeta, R. W., T. W. Simon, R. A. Oke, and W. W. Burd, 1998. Flow Measurements in Film Cooling Flows with Lateral Injection, ASME paper # 98-GT-54, presented at the 1998 Int'l. Gas Turbine Conf., Stockholm, Sweden.

63. Burd, S. W. and T. W. Simon, 1998. Turbulence Spectra and Length Scales Measured in Film Coolant Flows Emerging from Discrete Holes, 98-GT-190, presented at the 1998 Int'l. Gas Turbine Conf., Stockholm, Sweden, in J. of Turbomachinery (also a journal publication).

64. Burd, S. W. and T. W. Simon, 1998. Measurements of Discharge Coefficients in Film Cooling, ASME Paper # 98-GT-009, presented at the 1998 Int'l. Gas Turbine Conf., Stockholm, Sweden, also to be published in the J. of Turbomachinery (also a journal publication).

65. Burd, S. W., R. A. Oke, and T. W. Simon, 1998. Measurements of Aerodynamic Penalties Associated with Film Cooling, ASME HTD Vol. 361-3/PID Vol. 3, pp. 433-440, 1998 International Mechanical Engineering Congress and Exposition (IMECE), Anaheim, CA.

66. Oke, R. A. and T. W. Simon, 1998. A Study of Film Cooling Injection Geometries: Measured Flow and Thermal Fields with Lateral, Compound, and In-Line Injection, ASME HTD Vol. 361-3/PID Vol. 3, pp. 425-432, 1998 International Mechanical Engineering Congress and Exposition (IMECE), Anaheim, CA.

67. Oke, R. A. and T. W. Simon, 2000, Measurements in Film Cooling with Lateral Injection: Adiabatic Effectiveness Values and Temperature Fields, ASME paper # 00-GT-597.

68. Khounsary, A. M., J. R. Mondt, and T. W. Simon, 1998, “Heat Transfer Education: Keeping it Relevant and Vibrant,” HTD-Vol. 361-3/PID-Vol. 3, Proceedings of the 1998 International Mechanical Engineering Congress and Exposition (IMECE), Anaheim, CA.

69. Satterness C., T. W. Simon, and R. Oke, 1999, “An Experimental Investigation of Lateral Injection Film Cooling Heat Transfer,” Paper # AJTE99-6206, Proceedings of the 1999 ASME/JSME Thermal Engineering Joint Conference, San Diego, CA.

70. Aichlmayr, H. T., F. A. Kulacki, T.W. Simon, and P. J. Strykowski, 1999, “Technology-Based Education in Thermo-Fluids and Heat Transfer Engineering: A Status Report for 1998, Paper # AJTE99-6299, Proc. the 1999 ASME/JSME Thermal Engr. Joint Conference, San Diego, CA.

71. Kaszeta, R. W. and T. W. Simon, 1999, “Measurement of Eddy Diffusivity of Momentum in Film Cooling Flows with Streamwise Injection, ASME Paper # 99-GT-37, 1999 Int’l. Gas Turbine Conf., Indianapolis, IN, also to be in the J. of Turbo. (also a journal publication).

72. Burd, S. W. and T. W. Simon, 2000, “Flow Measurements in a Nozzle Guide Vane Passage with a Low Aspect Ratio and Endwall Contouring,” ASME paper # 00-GT-213, 2000 International Gas Turbine Congress, Munich, Germany. (also a journal publication).

73. Burd, S. W. and T. W. Simon, 2000, “Effects of Bleed Injection on Nozzle Guide Vane Performance: Flow Field Measurements,” ASME paper # 00-GT-199, 2000 Int’l. Gas Turbine Congress, Munich, Germany.

74. Burd, S. W., C. J. Satterness, T. W. and Simon, 2000, “Effects of Bleed Injection on Nozzle Guide Vane Performance: Thermal Measurements,” ASME paper # 00-GT-200, 2000 Intl. Gas Turbine Congress, Munich, Germany.

75. Oke, R. A., T. W. Simon, and R. Vahlberg, 2000, “Measurements in a Turbine Cascade over a Contoured Endwall: Discrete Hole Injection of Bleed Flow,” ASME paper # 00-GT-214 2000 International Gas Turbine Congress, Munich, Germany.

76. T. I-P. Shih, Y.-L. Lin, and T. W. Simon, 2000 “Control of Secondary Flows in a Turbine Nozzle Guide Vane by Endwall Contouring,” 2000-T-0556, 2000 Intl. Gas Turbine Conf., Munich, Germany.

77. K. W. Van Treuren, T. W. Simon, M. Von Koller, A. R. Byerley, R. Rivir, and J. W. Baughn, “Measurements in a Turbine Cascade Flow under Ultra Low Reynolds Number Conditions,” 2001-GT-0164, 2001 Intl. Gas Turbine Conf., New Orleans, LA, (also a journal publication).

78. R. W. Kaszeta, T. W. Simon, and D. P. Ashpis, 2001 “Experimental Investigation of Transition to Turbulence as Affected by Passing Wakes,” 2001-GT-0195, 2001 International Gas Turbine Conference, New Orleans, LA.

79. R. A. Oke, T. W. Simon, T. Shih, B. Zhu, Y. L. Lin, and M. Chyu, 2001,“Measurements over a Film-Cooled, Contoured Endwall with Various Coolant Injection Rates,” 2001-GT-0140, 2001 International Gas Turbine Conference, New Orleans, LA..

80. B. Zhu, Y-L. Lin, T. I-P. Shih, R. Oke, T. W. Simon and M. Chyu, 2001, “Computational Study of a Two-Passage Turbine Guide-Vane Cascade with End-Wall Contouring,” DETC-CIE-21762, presented at the 2001 ASME Computers and Information Engineering Conference, Pittsburgh, PA.

81. M. B. Ibrahim, R. C. Tew, Z. Zhang, T. W. Simon, and D. Gedeon, 2001, “CFD Modeling of Free-Piston Stirling Engines,” 2001, IECEC2001-CT-38, 2001 IECEC Conference, Savannah, GA.

82. R. A. Oke, and T. W. Simon, 2002, “Film Cooling Experiments with Flow Introduced Upstream of a First Stage Nozzle Guide Vane through Slots of Various Geometries,” 2002-GT-30169, 2002 International Gas Turbine Conference, Amsterdam, the Netherlands.

83. Byerley, A. R., O. Stormer, J. W. Baughn, T. W. Simon, K. W. VanTreuren, and J. List, “Using Gurney Flaps to Control Laminar Separation of Linear Cascade Blades,” ASME Paper GT-2002-30662, Proc. 2002 International Gas Turbine Conference, Amsterdam, (also a journal publication).

84. Niu, Y., T. W. Simon, M. B. Ibrahim, and D. Gedeon, D., 2002, “Oscillatory Flow and Thermal Field Measurements at the Interface between a Heat Exchanger and a Regenerator of a Stirling Engine,” IECEC 2002 Paper No. 20141, 2002 IECEC Conf.

85. Adolfson, D. A., T. W. Simon, M. B. Ibrahim, and D. Gedeon, 2002, “Measurements in Oscillatory Flows with Separation in Support of Stirling Engine Model Development,” IECEC 2002 Paper No. 20142, 2002 IECEC Conf.

86. Ibrahim, M. B., Z. Zhang, R. Wei, T. W. Simon, and D. Gedeon, 2002, “A 2-D CFD Modeling of Oscillatory Flow with Jets Impinging on a Random Wire Regenerator Matrix,” IECEC 2002 Paper No. 20144, 2002 IECEC Conf.

87. Ibrahim, M. B., S. Kembhavi, T. W. Simon, and D. Gedeon, 2002, “A 2-D Axisymmetric CRD Modeling of Oscillatory Flow with Separation,” IECEC 2002 Paper No. 20121, IECEC Conf.

88. Niu, Y., T. W. Simon, M. B. Ibrahim, and D. Gedeon, 2003, “Thermal Dispersion of Discrete Jets upon Entrance to a Stirling Engine Regenerator under Oscillatory Flow Conditions,” JSME TED-AJ03-641, 6th ASME-JSME Thermal Engineering Joint Conference.

89. Tew, R. C., J. E. Cairelli, M. B. Ibrahim, T. W. Simon, and D. Gedeon, 2003, “Overview of NASA Multi-Dimensional Stirling Convertor Code Development and Validation Effort,” Space, Technology and Applications Intl. Forum (STAIF-2003), Albuquerque, MN, February 2-6, 2003.

90. Jiang, N. and T. W. Simon, 2003, “Modeling Laminar-to-Turbulent Transition in a Low-pressure Turbine Flow which is Unsteady due to Passing Wakes: Part I, Transition Onset,” ASME GT2003-38787, 2003 Int’l. Gas Turbine Conference, Atlanta, GA.

91. Jiang, N. and T. W. Simon, 2003, “Modeling Laminar-to-Turbulent Transition in a Low-pressure Turbine Flow which is Unsteady due to Passing Wakes: Part II Transition Path,” ASME GT2003-38963, 2003 Int’l. Gas Turbine Conference, Atlanta, GA.

92. Kaszeta, R. W., T. W. Simon, F. Ottaviani, and N. Jiang, 2003, “The Influence of Wake Passing Frequency and Elevated Free Stream Turbulence Intensity on Transition in Low-Pressure Turbines,” AIAA-2003-3633 AIAA Thermophysics Conference, Orlando, FL.

93. Witkowski, T., S. White, C. O. Duenas, P. J. Strykowski, and T. W. Simon, 2003, Characterizing the Performance of the SR-30 Turbojet Engine,” ASEE paper #2003-1397, 2nd ASEE international Colloquium on Engineering Education, Nashville, TN, June 20-22.

94. Niu, Y., T. W. Simon, M. B. Ibrahim, R. Tew, and D. Gedeon, D., 2003, “Measurements of Unsteady Convective Heat Transfer Rates within a Stirling Regenerator Matrix Subjected to Oscillatory Flow,” Paper # AIAA-2003-6013, 2003 International Energy Conversion Engineering Conference, Portsmouth VA.

95. Niu, Y., T. W. Simon, M. B. Ibrahim, R. C. Tew, and D. Gedeon, 2003, “Jet Penetration into a Stirling Engine Regenerator Matrix with Various Regenerator-Cooler Spacings,” Paper # AIAA-2003-6014, 2003 International Energy Conversion Engineering Conference, Portsmouth VA.

96. Adolfson, D. A., T. W. Simon, M. B. Ibrahim, and D. Gedeon, 2003, “Unsteady Fluid Dynamics Simulation of a Stirling Engine Heater Head,” Paper # AIAA-2003-5934, 2003 International Energy Conversion Engineering Conference, Portsmouth VA.

97. Jiang, N. and T. W. Simon, 2003, “The Influence of Unsteady Acceleration and Turbulence Intensity on Transition in low-Pressure Turbines,” AIAA-2003-3630, AIAA Thermophysics Conference, Orlando, FL. (also a journal publication).

98. Ibrahim, M. B., Z. Zhang, S. Kembhavi, T. W. Simon, R. Tew, and D. Gedeon, 2003, “A Model of 90 Degree Turn Oscillatory Flow,” Paper # AIAA-2003-5935, 2003 International Energy Conversion Engineering Conference, Portsmouth VA.

99. Ibrahim, M. B., W. Rong, T. W. Simon, R. Tew, R., and D. Gedeon, 2003, “Microscopic Modeling of Unsteady Convective Heat transfer in a Stirling Regenerator Matrix,” Paper # AIAA-2003-6016, 2003 International Energy Conversion Engineering Conference, Portsmouth VA.

100. Adolfson, D. A., T. W. Simon, and M. B. Ibrahim, 2004, “Measurements, Computation and Analysis of a Semi-Constrained, Axisymmetric Jet,” ASME GT2004-54215, 2004 Int’l. Gas Turbine Conference, Vienna Austria.

101. Piggush, J. D. and T. W. Simon, 2004, “Experimental Investigation and Documentation of Endwall Streamwise Contouring Benefits in First Stage Nozzle Passages,” ASME GT2004-54202, 2004 Int’l. Gas Turbine Conference, Vienna Austria.

102. Tew, R. C., M. B. Ibrahim, T. W. Simon, S. Mantell, D. Gedeon, S. Qiu and G. Wood, 2004, “Overview 2003 of NASA Multi-Dimensional Stirling Convertor Code Development and DOE & NASA Stirling Regenerator R & D Efforts,” Space, Technology and Applications International Forum (STAIF-2004), Albuquerque, NM, February 8-12, 2004.

103. Jiang, N. and T. W. Simon, 2004, “Evaluation of Algebraic Transition Models for Application to Unsteady Flows in Low-Pressure Turbines,” ASME GT2004-54223, 2004 Int’l. Gas Turbine Conference, Vienna Austria.

104. Ibrahim, M. B., S. Veluri, T. W. Simon, and D. Gedeon, 2004, “CFD Modeling of Surface Roughness in Laminar Flow,” 2nd International Energy Conversion Engineering Conference, AIAA-2004-5585, Aug. 16-19, 2004, Providence, R.I.

105. Sun, L., S. C. Mantell, D. Gedeon, and T. W. Simon, 2004, “A Survey of Microfabrication Techniques for Use in Stirling Engine Regenerators,” 2nd International Energy Conversion Engineering Conference, AIAA-2004-2004-5647, Aug. 16-19, 2004, Providence, R.I.

106. Niu, Y., T. W. Simon, D. Gedeon, D., and M. B. Ibrahim, 2004, “On Experimental Evaluation of eddy Transport and Thermal dispersion in Stirling Regenerators,” 2nd International Energy Conversion Engineering Conference, AIAA-2004-5646, Aug. 16-19, 2004, Providence, R.I.

107. Piggush, J. and T. W. Simon, 2005, :Flow Measurements in a First Stage Nozzle Cascade having Endwall Contouring, ASME GT2005-68340, 2005 International Gas Turbine Conf., Reno, NV.

108. Ibrahim, M. B., B. J. Kochuparambil, S. V. Ekkad, T. W. and Simon, 2005, “CFD for Jet Impingement Heat Transfer with Single Jets and Arrays,” GT2005-68341, 2005 International Gas Turbine Conference, Reno, NV.

109. Niu, Y., G. McFadden, T. W. Simon, M. Ibrahim, and W. Rong, W., 2005, “Measurements and Computation of Dispersion in a Porous Medium,” 3rd International Energy Conversion Engineering Conference, AIAA-2005-5578, Aug. 15-18, 2005, San Francisco, CA.

110. Ibrahim, M. J. Keister, L. Sun, T. W. Simon, S. Mantell, D. Gedeon, D. Guidry, S. Qiu, and G. Wood, 2005, “Assessing the Performance of the Microfabricated Regenerator for the Stirling Space Power Convertor” 3rd International Energy Conversion Engineering Conference, AIAA-2005-5597, Aug. 15-18, 2005, San Francisco, CA.

111. Ibrahim, M. B., M. Mittal, N. Jiang, and T. W. Simon, 2005, “Validation of Multi-Dimensional Stirling Engine Codes: Modeling of the Heater Head,” 3rd International Energy Conversion Engineering Conference, AIAA-2005-5654, Aug. 15-18, 2005, San Francisco, CA.

112. Piggush, J. D. and T. W. Simon, 2005. “Heat Transfer Measurements in a First Stage Nozzle Cascade having Endwall Contouring, Leakage and Assembly Features, ASME HT2005-72573, 2005 National Heat Transfer Conference San Francisco, CA. (also a journal publication)

113. Piggush, J. D. and T. W. Simon, 2005. “Flow Measurements in a First Stage Nozzle Cascade having Leakage and Assembly Features: Effects of Endwall Steps and Leakage on Aerodynamic Losses,” ASME IMECE2005-83032, 2005 ASME IMECE, Orlando, FL.

114. Piggush, J. D. and Simon, T. W., 2006. “Heat Transfer Measurements in a First Stage Nozzle Cascade having Endwall Contouring: Misalignment and Leakage Studies,” GT2006-90575, 2006 International Gas Turbine Conference, Barcelona, Spain.

115. Piggush, J. D. and T. W. Simon, 2006. “Adiabatic Effectiveness Measurements in a First Stage Nozzle Cascade having Endwall Contouring, Leakage and Assembly Features,” GT2006-90576, 2006 International Gas Turbine Conference, Barcelona, Spain.

116. Tew, R., T. Simon, R. Dyson, S. Wilson, D. Gedeon, M. Ibrahim, W. Rong, and R. Demko, 2006, “An Initial Non-Equilibrium Porous-Media Model for CFD Simulation of Stirling Regenerators,” Paper AIAA 2006-4003 4th International Energy Conversion and Engineering Conference, 26-29 June 2006, San Diego, CA.

117. Simon, T., G. McFadden, and M. Ibrahim, 2006, “Thermal Dispersion within a Porous Medium near a Solid Wall,” Paper # 1198.00, Proc. of the 13th International Heat Transfer Conference, Sydney Australia, August 13-18.

118. Piggush, J. D., and T. W. Simon, 2006, “Measurements of Net Change in Heat Flux as a Result of Leakage and Steps on the Contoured Endwall of a Gas Turbine First Stage Nozzle,” ASME/ATI Conference on Energy: production, distribution, and conservation, Milan, Italy, May (also a journal publication).

119. Jiang, N. and T. W. Simon, 2006, “Heat Transfer and Fluid Dynamics Measurements in the Expansion Space of a Stirling Cycle Engine,” IMECE2006-15631, IMECE2006 Conference.

120. Simon, T., Chandra, S., Kulacki, F. and Sefiane, K., 2006, Discussion Panel on Heat Transfer Education, Proc. of the 13th International Heat Transfer Conference, Sydney Australia, August 13-18.

121. Tew, R., M. Ibrahim, T. Simon, S. Mantell, L. Sun, D. Gedeon, K. Kelly, J. McLean, G. Wood, and S. Qiu, S., 2007, A Microfabricated Involute-Foil Regenerator for Stirling Engines, Paper AIAA-2007-4739, 5th International Energy Conversion and Engineering Conference, 25-27 June 2007, St. Louis, MO.

122. Sun, L., T. Simon, S. Mantell, M. Ibrahim, D. Gedeon, and R. Tew , 2008, Jet Penetration into a Scaled Microfabricated Stirling Cycle Regenerator, Paper AIAA-2008-5719, 6th International Energy Conversion and Engineering Conference (IECEC), 28-30 June 2008, Cleveland, OH.

123. Mamunuru, M., S. Guo, D. Poon, D. Burman, T. Simon, D. Ernie, and U. Kortshagen, 2009, “Separation Control using Plasma Actuator: Simulation of Plasma Actuator,” AIAA2009-4186, 39th AIAA Fluid Dynamic Conference, 22-25 June, 2009 San Antonio, TX, 2009.

124. Guo, S., D. Burman, D. Poon, M. Mamunuru, T. Simon, D. Ernie, and U. Kortshagen, 2009, “Separation Control using Plasma Actuator: Designs for Thrust Enhancement,” AIAA2009-4184, 39th AIAA Fluid Dynamic Conference, 22-25 June, 2009 San Antonio, TX, 2009.

125. Sun, L., T. Simon, S. Mantell, D. Gedeon. M. Ibrahim, and R. Tew, R., 2009,“Thermo-fluid Experiments Supporting Microfabricated Regenerator Development for a Stirling Space Power Engine,” 7th International Energy Conversion and Engineering Conference (IECEC), 3-5 August 2009, Denver, CO.

126. Ganesan, K., T. Simon, and J. Quinnell, 2009, “Flow through Stirling engine regenerators with and without a gap between the matrix and container wall – Part 1: Computation,” 7th International Energy Conversion and Engineering Conference (IECEC), 3-5 August 2009, Denver, CO.

127. Quinnell, J., T. Simon, and K. Ganesan, 2009, “Flow through Stirling Engine Regenerators with and without a Gap between the Matrix and Container Wall: Part 2: Experiments,” 7th International Energy Conversion and Engineering Conference (IECEC), 3-5 August 2009, Denver, CO.

128. Kortshagen, U., S. Guo, M., Mamunuru, D. Ernie, and T. Simon, 2009, “Experiments and Simulation of Plasma Actuators with Enhanced Thrust,” 19th International Symposium on Plasma Chemistry in Bochum, Germany, July 27-31, 2009.

129. Erickson, R. and Simon, T., 2009, “Effects of Stator/Rotor Leakage Flow and Axisymmetric Contouring on Endwall Adiabatic Effectiveness and Aerodynamic Loss,” Int. Symp. on Heat Transfer in Gas Turbine Systems, August 9-14, Antalya, Turkey (also a journal publication).

130. Guo, S., D. Burman, D. Poon M, Mamunuru, T. Simon, D. Ernie, and U. Kortshagen, 2010, “Separation Control using Plasmas Actuator: Thrust Enhancement Studies,” AIAA 2010-1090, 48th AIAA Aerospace Sciences Meeting, Orlando FL, 2010.

131. Mamunuru, M., T. Simon, D. Ernie, and U. Kortshagen, 2010,“Separation Control using Plasma Actuator: Simulation of Plasma Actuator,” AIAA 2010-1221, 48th AIAA Aerospace Sciences Meeting, Orlando FL, 2010.

132. Burman, D., T. Simon, U. Kortshagen, and D. Ernie, 2010, “Separation Control using Plasma Actuator: Steady Flow in Low Pressure Turbines,” AIAA 2010-1220, 48th AIAA Aerospace Sciences Meeting, Orlando FL, 2010.

133. Poon, D. T. Simon, U. Kortshagen, and D. Ernie, 2010, “Experimental Studies of Plasma Actuator Performance for Separation Control, AIAA 2010-1219, 48th AIAA Aerospace Sciences Meeting, Orlando FL, 2010.

134. Burman, D., Simon, T., Kortshagen, U, and Ernie, D., “Separation Control using Plasma Actuators: Steady Flow in Low Pressure Turbines,” GT2011-46807, Proceeding of the ASME Turbo Expo 2011 Conference, Vancouver, Canada, June 6-10, 2011.

135. Erickson, R., Simon, T., Zhang, L., Moon, H-K., “Experimental Investigation of Disc Cavity Leakage Flow and Hub Endwall contouring in a Linear rotor Cascade, GT2011-46700, Proceeding of the ASME Turbo Expo 2011 Conference, Vancouver, Canada, June 6-10, 2011.

136. Li, P., Loth, E., Simon, T., Van de Ven, J., and Crane, S., “Compressed Air Energy Storage for Offshore Wind Turbines,” Presented at the IFPE (International Fluid Power Exposition) March 22-26, 2011, Las Vegas, NV.

137. Qin, C., Loth, E., Li, P., Simon, T., Van de Ven, J., and Crane, S., Spray-enhanced Fluid Compression for Wind Energy storage and Regeneration,” Presented at the IFPE (International Fluid Power Exposition) March 22-26, 2011, Las Vegas, NV.

138. Zhang, M., Simon, T. W., Huang, L., Selvi, V., North, M., and Cui, T., 2011, A Polymeric Piezoelectric Synthetic Jet for Electronic Cooling,“ IMECE2011-64392, ASME 2011 Int’l. Mech. Engr. Congress and Expo, IMECE2011, Denver CO.

139. Yeom, T., Simon, T. W., Yu, Y., North, M. and Cui, T., 2011, “Convective Heat Transfer Enhancement on a Channel Wall with a High Frequency, Oscillating Agitator,” IMECE2011-64379, ASME 2011 Int’l. Mech. Engr. Congress and Expo, IMECE2011, Denver CO.

140. Huang, L., Simon, T. W., North, M. and Cui, T., 2011, “Experimental and Numerical Simulation of a Synthetic Jet for Cooling of Electronics,” IMECE2011-64574, ASME 2011 Int’l. Mech. Engr. Congress and Expo, IMECE2011, Denver CO.

141. Yu, Y., Simon, T. W., Agrawal, S., North, M. and Cui, T., 2011, “A Computational Study of Active Heat Transfer Enhancement of Air-Cooled Heat Sinks by Actuated Plates,” IMECE2011-64526, ASME 2011 Int’l. Mech. Engr. Congress and Expo, IMECE2011, Denver CO.

142. Yu, Y., Simon, T. W., Zhang, M., Yeom, T., North, M. and Cui, T., 2011, “Enhancing Heat Transfer of Air-Cooled Heat Sinks using Piezoelectrically-Driven Agitators and Synthetic Jets,” IMECE2011-64544, presented at the ASME 2011 Int’l. Mech. Engr. Congress and Expo, IMECE2011, Denver CO.

143. Agrawal, S., Y., Simon, T. W., North, M. and Cui, T., 2011, “An Experimental Study on the Effects of Agitation on Forced-Convection Heat Transfer,” IMECE2011-64558, presented at the ASME 2011 Int’l. Mech. Engr. Congress and Expo, IMECE2011, Denver CO.

144. Yu, Y., Simon, T. W., North, M. T., and Cui, T., 2012, “Comparison of Heat Transfer Enhancement by Active Plates in Heat-Sink Channels,” ASME Summer Heat Transfer Conference, Puerto Rico, USA, July 8-12, 2012. Paper # HT2012-58280.

145. Huang, L., Zhang, M., North, M. T., Cui, T., and Simon, T. W., 2012, “Heat Transfer Enhancement by Synthetic Jet Arrays in Air-cooled Heat sinks for use in Electronics Cooling,” ASME Summer Heat Transfer Conference, Puerto Rico, USA, July 8-12, 2012. Paper # HT2012-58278.

146. Agrawal, S., Simon, T., North, M., and Cui, T., 2012, “An Experimental Study on the Effects of Agitation in Generating Flow Unsteadiness and Enhancing Convective Heat Transfer,” ASME Summer Heat Transfer Conference, Puerto Rico, USA, July 8-12, 2012. Paper # HT2012-58273

147. Zhang, M., Yeom, T., Yu, Y., Huang, L., Simon, T., North, M., Cui, T., 2012, “Development of Synthetic Jet Arrays for Heat Transfer Enhancement in Air-Cooled Heat Sinks for Electronics Cooling,” ,” ASME Summer Heat Transfer Conference, Puerto Rico, USA, July 8-12, 2012. Paper # HT2012-58273.

148. Wang, C., Yu, Y., Simon, T., Cui, T. and North, M., 2012, “Microfabrication of Short Pin Fins on Heat Sink Surfaces to Augment Heat Transfer Performance,” ITherm-2012 Paper # 2012_3050.

149. Saadat, M., Li, P., and Simon, T. W., 2012, “Optimal Trajectories for a Liquid Piston Compressor/Expander in a Compressed Air Energy Storage System with Consideration of Heat Transfer and Friction,” 2012 American Control Conference, Montréal, Canada, June 27-June 29.

150. Huang, L., Agrawal, S. Simon, T. W., Zhang, M., Yeom, T., North, M. T., and Cui. T., 2012, “Fluid Damping and Power Consumption of Active Devices used in Cooling Electronics,” IMECE2012-88627, Houston, TX.

151. Huang, L., Simon, T., Zhang, M., Yeom, T., North, M. T., and Cui, T., 2012, “Noise Measurements and Reduction for High-frequency Vibrating devices in the Application of Cooling Electronics,” IMECE2012-88638, Houston, TX.

152. Yeom, T., Simon, T. W., Zhang, T., North, M. T. and Cui, T., 2012, “Convective Heat Transfer Enhancement with Micro Pin-Fin Surfaces Cooled by a Piezoelectrically-driven Translational,” Agitator, IMECE2012-88428, Houston, TX.

153. Yeom, T., Simon, T.W., Yu, Y., Zhang, M., Agrawal, S., Huang, L., Zhang, T., North, M. T., and Cui, T., 2012, “An Active Heat Sink System with Piezoelectric Translational Agitators and Micro Pin Fin Arrays,” IMECE2012-88449, Houston, TX.

154. Zhang, C., Saadat, M., Li, P., and Simon, T. W., 2012, “Heat Transfer in a Long, Thin Tube Section of an Air Compressor: An Empirical Correlation from CFD and Thermodynamic Modeling, IMECE2012-86673, Houston, TX.

155. Zhang, C., Simon, T. W., and Li, P., 2012, “Storage Power and Efficiency Analysis Based on CFD for Air Compressors used for Compressed Air Energy Storage,” IMECE2012-88985, Houston, TX.

156. Saadat, M., Li, P. and Simon, T., 2012 “Optimal Trajectories for a Liquid Piston Compressor-Expander in a Compressed Energy Storage System with Consideration of Heat Transfer and Friction,” 2012 American Control Conference, Montreal, Canada, June 2012.

157. Qin, C., Loth, E., Li, P., Simon, T., Van De Ven, J., Crane, S., and Pourmousa, A., 2013, “Spray-Cooling for Wind-Based Compressed Air Energy Storage,” 49th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit and 11th International Energy Conversion Engineering Conference, San Jose, CA, July 2013.

158. Shirazi, F. Saadat, M., Yan, B., Li, P. and Simon, T., 2013 “Optimal Control Experimentation of Compression Trajectories for a Liquid Piston Air Compressor,” HT2013-17613, ASME Summer Heat Transfer Conference, Minneapolis, MN.

159. Agrawal, S., Huang, L., Simon, T., North, M., and Cui, T., 2013, “Effects of Channel Aspect Ratio on Convective Heat Transfer in an Electronics Cooling Heat Sink Having Agitation and Fan-Induced Throughflow,” HT2013‑17182, ASME Summer Heat Transfer Conference, Minneapolis, MN.

160. Ayaskanta, A., Huang, L., Simon, T., Yeom, T., North, M. and Cui, T., 2013, “Heat Transfer Enhancement of a Heat Sink by Inclined Synthetic Jets for Electronics Cooling,” HT2013‑17769, ASME Summer Heat Transfer Conference, Minneapolis, MN.

161. Zhang, C., Shirazi, F., Yan, B., Simon, T., Li, P., Van de Ven, J. 2013, “Design of an Interrupted-Plate Heat Exchanger Used in a Liquid-Piston Compression Chamber for Compressed Air Energy Storage,” HT2013‑17484, ASME Summer Heat Transfer Conference, Minneapolis, MN.

162. Shirazi, F., Saadat, M. Yan, B., Li, P., Simon, T., 2013, "Iterative Optimal and Adaptive Control of a Near Isothermal Liquid Piston Air Compressor in a Compressed Air Energy Storage System," 2013 ACC IEEE Control Systems Society Conference, Paper No. 1702, 2013 American Control Conference, Washington, DC.

163. Seah, Y. Erickson, R, Simon, T., Moon, H-K, and Zhang, L., 2013, Effects of Combustor Exit Temperature Profile on Adiabatic Effectiveness of Leakage Flow Film Cooling over an Axisymmetric Endwall, GT2013-96032, 2013 Turbo-Expo Conference, San Antonio, TX.

164. Li, Q., Huang, L., North, M., Simon, T. and Cui, T., 2013, Piezoelectric Synthetic Jet Integrated with Heat Sink for Heat Transfer Enhancement,” IMECE2013-62634, 2013 IMECE conference, San Diego, CA.

165. Zhang, C., Wieberdink, J., Shirazi, F., Yan, B., Simon, T., Li, P., 2013, “Numerical Investigation of Metal-Foam Filled Liquid Piston Compressor Using a Two-Energy Equation Formulation Based on Experimentally Validated Models,” IMECE2013-63854, 2013 IMECE conference, San Diego, CA.

166. Ayaskanta, A., Simon, T. Erickson, R., Moon, H-K., Zhang, L., 2013, “High Pressure Turbine Rotor Stage Endwall Cooling and Passage Thermal Fields as affected by Leakage Flow and Combustor Liner Coolant Streams,” IMECE 2013-65601, 2013 IMECE conference, San Diego, CA.

167. Zhang, C., Simon, T., Li, P., 2013, “Optimization of the Axial Porosity Distribution of Porous Inserts in a Liquid Piston Gas Compressor using a One-Dimensional Formulation,” IMECE2013-63862, 2013 IMECE conference, San Diego, CA.

168. Zhang, C. Simon, T. W. Li, P. Y., and Van de Ven, J., 2014, “Numerical Modeling of Three Dimensional Heat Transfer and Fluid Flow through Interrupted Plates using Unit Cell Scale,” Proceedings of the 15th International Heat Transfer Conference, IHTC-15, August 10-15, 2014, Kyoto, Japan

169. Chao Qin, Eric Loth, Perry Li, Terrence Simon, James D. Van De Ven, Stephen Crane, and Amir Pourmousa. "Spray-Cooling for Wind-Based Compressed Air Energy Storage", 11th International Energy Conversion Engineering Conference, Joint Propulsion Conferences, (AIAA 2013-3870) http://dx.doi.org/10.2514/6.2013-3870 

170. Stinson, M., Goldstein, R. J., Simon, T. W. Fujimoto, S. and Nakamata, C., 2014, “Effect of Swirled Leakage Flow on Endwall Film-Cooling,” IHTC15-9600, Proceedings of the 15th International Heat Transfer Conference, IHTC-15, August 10-15, 2014, Kyoto, Japan.

171. Reich, L., Bader, R., Simon, T. W., and Lipinski, W., 2014, “Heat and Mass Transfer Model of a Packed-Bed Reactor for Solar Thermochemical CO2 Capture,” IHTC15-8893, Proceedings of the 15th International Heat Transfer Conference, IHTC-15, August 10-15, 2014, Kyoto, Japan.

172. Agrawal, S., Yeom, T. Yu, Y., North, M., Simon, T., and Cui, T., 2014, “The Effects of Agitator Blade Geometry and Configuration for Augmenting Heat Transfer by agitation in Channel Flows, IMECE2014-37303, ASME 2014 International Mechanical Engineering Congress and Exposition, November 14-20, Montreal, Canada.

173. Zhang, C., Simon, T. W., Wieberdink, J., Li, P. Y., Van de Ven, J., and Loth, E., 2014, “Numerical Analysis of Heat Exchangers used in a Liquid Piston Compressor using a One-Dimensional Model with an Embedded Two-Dimensional Sub-model,” IMECE2014-38567, ASME 2014 International Mechanical Engineering Congress and Exposition, November 14-20, Montreal, Canada.

174. Park, H., Osterhouse, D. J., Pfender, E., Simon, T. W. and Lindsay, J. W., 2014, “Three-Dimensional Two-Temperature Modeling of the Anode Region in Plasma Arc Cutting,” (Abstract) High-Tech Plasma Processes Conference (HTPP13), Toulouse France 22-27 June 2014.

175. Reich, L., Melmoth, L., Gresham, R., Simon, T., and Lipinski, W., 2015 “Design of a Solar Thermochemical Reactor for Calcium Oxide Based Carbon Dioxide Capture,” Paper #49507, Proceedings of the ASME 2015 Power & Energy Conf., San Diego, CA, June 28-July 2, 2015.

176. Li, J-Y., Guo, S-P., Zhang, J., Li, W., Wei, J-J., and Simon, T., 2015 “Single Phase and Two Phase Flow Characteristics and Heat Transfer in Micro-fin Tubes, InterPACKICNMM2015 conference (International Technical Conference and Exhibition on Packaging and Integration of Electronic and Photonic Microsystems and 12th International Conference on Nanochannels, Microchannels, and Minichannels), July 2015.

177. Agrawal, S., North, M, Simon, T. and Cui, T., 2015 “Unsteady Heat Flux Measurements in Agitated Channel Flows,” InterPACKICNMM2015 conference, Paper No. IPACK2015-48753, pp. V001T09A009; doi:10.1115/IPACK2015-48753, July 2015.

178. Ayaskanta, A., Simon, T., and Saxena, R., 2015 “Flow Migration and Mixing in a High Pressure Turbine Rotor Passage with Axisymmetrically Contoured Endwall and Leakage Flow,’ GT2015-44000, Proceedings of the Turbo-Expo International Gas Turbine Conference, Montreal, Canada, June 2015.

179. Reich, L., Bader, R., Simon, T., and Lipinski, W., “Thermal Transport Model of a Packed-Bed Reactor for Solar Thermochemical CO2 Capture,” AIChE Annual Mtg. (same as A-70)

180. Reich, L., Melmoth, L., Gresham, R., Simon, T., and Lipinski, W., 2015,“Thermal and Mechanical Design of a Solar-Driven Reactor for Calcium Oxide based Carbon Dioxide Capture,” Proc. ASME 2015 Power and Energy Conference, PowerEnergy2015 June 28-July 2, San Diego Ca., PowerEnergy2015-49507

181. Huang, L, Hummelt, E., Simon, T., and Li, P., 2015 “Analysis of Dissolved Gas in the Application of Liquid Piston Gas Compression,” American Society of Thermal and Fluids Engineers First Thermal and Fluids Engineering Summer Conference (TFESC-12869), August 2015.

182. Zhang, C., Li, P., Van de Ven, Simon, T., 2015 “Design Analysis of a Liquid-Piston Compression Chamber with Application to Compressed Air Energy Storage,” ASME-ATI-UIT 2015 Conference on Thermal Energy Systems: Production, Storage, Utilization and the Environment, Napoli Italy, 2015, ISBN 978-88-98273-17-1

183. Yue, L., Reich, L., Simon, T., Bader, B. and Lipinski, W., 2015 Solar Thermochemical CO2 Capture via Calcium Oxide Looping: Thermal Transport Modeling and Solar Reactor Design, 2015 AIChE Annual Meeting in Salt Lake City, UT, November

184. Yue, L., Reich, L., Simon, T., Bader, R., and Lipiński, W., 2015, “Solar Thermochemical CO2 Capture via Calcium Oxide Looping: Thermal Transport Modeling and Solar Reactor Design,” Eurotherm, abstract accepted for Seminar No 109, Numerical Heat Transfer 2015, 27-30 September 2015, Gliwice-Warsaw, Poland, Eds.: A.J. Nowak, J. Banaszek, B. Šarler

185. Liu, Z., Yang, X., Li, J. Feng, Z., and Simon, T. 2016, ”Effect of Bleed Position and Bleed Angle on Impingement Cooling of a Spherical-Dimpled Surface,” GT2016-57540, Proceedings of ASME Turbo Expo 2016, Seoul, Korea.

186. Saxena, R., Alqefl, M., Liu, Z., Moon, H-K. Zhang, L., and Simon, T., 2016, “Contoured Endwall Flow and Heat Transfer Experiments with Combustor Coolant and Gap Leakage Flows for a Turbine Nozzle Guide Vane, GT2016-56675, Proceedings of ASME Turbo Expo 2016, Seoul, Korea.

187. Yue, Lindsey, Reich Leanne, Simon, Terrence Simon, Bader, Roman, Lipinski, Wojciech, 2016, "Progress in thermal transport modeling of carbonate-based reacting systems" International Journal of Numerical Methods for Heat and Fluid Flow

188. Zhang, C., Li, P., Van de Ven, J., and Simon, T., 2017, Oscillatory flow regenerative heat exchangers for application to energy storage systems, TFEC-IWHT2017-17911, 4th Int’l. Workshop on Heat Transfer, Las Vegas, NV.

189. Alqefl, M., Kim, Y., Moon, H-K., Zhang, L., and Simon, T., Numerical study of contoured endwall flow and heat transfer with combustor coolant and film cooling flows for a turbine nozzle guide vane, TFEC-IWHT2017-18417, 4th Int’l. Workshop on Heat Transfer, Las Vegas, NV.

190. Liu, Z., Li, J. Feng, Z. and Simon, T., 2017, A numerical study of the effects of number of jets on swirl cooling of a gas turbine blade leading edge, TFEC-IWHT2017-17934, , 4th Int’l. Workshop on Heat Transfer, Las Vegas, NV.

191. Yue, Lindsey, Simon, Terrence and Lipiński, Wojciech, 1027, Experimental investigation of carbon dioxide capture and high-temperature thermal energy storage via metal oxide chemical looping in a 1 kW solar prototype reactor, HT2017-5121, ASME Summer Heat Transfer Conference, Bellevue WA.

192. Zhu, Rui, Yan, Hongbin, Xie, Gongnan, and Simon, Terrence, 2017, Enhanced film cooling effectiveness by integration of horn-shaped and cylindrical holes, HT2017-4764, ASME Summer Heat Transfer Conference, Bellevue WA.

193. Song, Y., Zhu, R., Simon, T., Xie, G., 2017, Flow Patterns, Drag and Lift for Low Reynolds Number Flow past Tandem Cylinders of Various Shapes, IMECE2017-70089, Tampa, FL.


Other Technical Publications

1. Simon, T. W. and C. M. Shields. 1973. "Core Spray Distribution," NEDO-10846, General Electric Licensing Topical Report.

2. Simon, T. W. 1980. "Turbulent Boundary Layer Heat Transfer Experiments: Convex Curvature Effects Including Introduction and Recovery", Ph.D. Thesis, Stanford University.

3. Simon, T. W., R. J. Moffat, J. P. Johnston, and W. M. Kays. 1982. "Turbulent Boundary Layer Heat Transfer Experiments: Convex Curvature Effects Including Introduction and Recovery", NASA CR-3510.

4. Simon, T. W. and R. J. Moffat. 1980. "Output for Standard Cases in the STAN5 Manual," IL-20, Stanford University, Department of Mechanical Engineering Internal Report.

5. Simon, T. W. 1984. "PLATO UDEC Program Development: Thermalscience Track-Thermodynamics, Fluid Mechanics, and Heat Transfer," Control Data Corporation internal report.

6. Wang, T. and T. W. Simon. 1984. "Heat Transfer and Fluid Mechanics Measurements in Transitional Boundary Layer Flow," in Transition in Turbines, NASA-CP 2386.

7. Simon, T. W. and J. Seume. 1988. "A Survey of Oscillating Flow in Stirling Engine Heat Exchangers," NASA-CR-182108.

8. Russ, S. and T. W. Simon. 1990. "Signal Processing Using the Orthogonal Triple-wire Equations," Flowlines, the TSI quarterly magazine, Winter1990, pp. 3-9.

9. Kim, J. and T. W. Simon. 1991. "Free-stream Turbulence and Concave Curvature Effects on Heated, Transitional Boundary Layers: Volume I - Final Report," NASA-CR 187150.

10. Kim, J. and T. W. Simon. 1991. "Free-stream Turbulence and Concave Curvature Effects on Heated, Transitional Boundary Layers: Volume II - Program Listings and Tabulated Data," NASA-CR 187151.

11. Volino, R. J. and T. W. Simon. 1991. "Bypass Transition in Boundary Layers Including Curvature and Favorable Pressure Gradient Effects," NASA-CR 187187.

12. Seume, J., G. Friedman, and T. W. Simon. 1992. "Fluid Mechanics Experiments in Oscillatory Flow, Volume 1 - Report," NASA-CR 189127.

13. Seume, J., G. Friedman, and T. W. Simon. 1992. "Fluid Mechanics Experiments in Oscillatory Flow, Volume 2 - Data," NASA-CR 189127.

14. Simon, T. W. and R. J. Volino, 1993. "Experiments in Transitional Boundary Layers with Emphasis on High Free-Stream Turbulence Level, Surface Concave Curvature and Strong Favorable Streamwise Pressure Gradient Effects," Proceedings from the Syracuse University Workshop on Transition.

15. Volino, R. J. and T. W. Simon. 1995. "Measurements in Transitional Boundary Layers under High Free-Stream Turbulence and Strong Acceleration Conditions," NASA-CR 198413.

16. Simon, T. W. and R. J. Goldstein. 1996 "Instrumentation for Fluid Dynamics--Random Error, Systematic Error, and Calibration," Handbook of Fluid Dynamics and Fluid Machinery, Wiley, NY.

17. Simon, T. W. and R. J. Goldstein. 1996. "Instrumentation for Fluid Dynamics--Methods of Data Analysis," Handbook of Fluid Dynamics and Fluid Machinery, Wiley, NY.

18. Simon, T. W. and R. J. Goldstein. 1996. "Instrumentation for Fluid Dynamics--Pressure Measurements," Handbook of Fluid Dynamics and Fluid Machinery, Wiley, NY.

19. Qiu, S. and T. W. Simon, 1998, “An Experimental Investigation of Transition as Applied to Low-Pressure Turbine Suction Surface Flows,” in Minnowbrook II, 1997 Workshop on Boundary Layer Transition in Turbomachines, NASA/CP-1998-206958.

20. Burd, S. W. and Simon, T. W., 2000, “Effects of Hole Length, Supply Plenum Geometry, and Freestream Turbulence on Film Cooling Performance, NASA/CR--2000-210336.

21. Simon, T. W., S. Qiu, and K. Yuan, 2000, "Measurements in a Transitional Boundary Layer under Low-Pressure Turbine Airfoil Conditions,” NASA-CR - 2000-209957.

22. Kaszeta, R. W and T. W. Simon, 2002, "Experimental Investigation of Transition to Turbulence as Affected by Passing Wakes", NASA-CR-2002-212104.

23. Byerley, A. R., O. Stormer, J. W. Baughn, T. W. Simon, and K. W. Van Treuren, “A ‘Cool’ Thermal Tuft for Detecting Surface Flow Direction,” IMECE Heat Transfer Photo Gallery, presented at the 2002 IMECE Conference, New York.

24. Ibrahim, M. B., R. C. Tew, Z. Zhang, D. Gedeon, and T. W. Simon, 2001, “CFD Modeling of Free-Piston Stirling Engines,”NASA/TM-2001-211132.

25. Simon, T. W., T. I-P Shih, and R. Pletcher, 2003, “Simulations of Turbulent Flow,” Summer 2003 Research Bulletin of the Univ. of Minnesota Supercomputer Institute for Digital Simulation and Advanced Computation, vol. 19, Number 3.

26. Tew, R. C., J. E. Cairelli, M. B. Ibrahim, T. W. Simon, and D. Gedeon, 2003, “Overview of NASA Multi-Dimensional Stirling Convertor Code Development and Validation Effort,” NASA/TM-2002-211997.

27. Adolfson, D. and T.W. Simon, 2006, “Validation of Multi-Dimensional Stirling Engine Design Codes: Measurements in the 90-Degree Turn Test Section,” NASA/CR-2006-214131.

28. Kaszeta, R. W., T. W. Simon, N. Jiang, and F. Ottaviani, 2007, "Experimental Investigation of Transition to Turbulence as Affected by Passing Wakes: Effects of High FSTI and Increased Rod Spacing", NASA/CR-2007-214678 (With attached CD).

29. Jiang, N. and T. W. Simon, 2006, “Heat Transfer and Fluid Dynamics Measurements in the Expansion Space of a Stirling Cycle Engine,” (IMECE2006-15631) NASA/CR-2006-214454, Dec. 2006.

30. Tew, R., T. Simon, D. Gedeon, M. Ibrahim, and W. Rong, 2006, “An Initial Non-Equilibrium Porous-Media Model for CFD Simulation of Stirling Regenerators,” NASA/TM-2006-214391 (item D-116, above).

31. Simon, T. and J. Piggush, 2008, “Hot Gas Path Heat Transfer Characteristics/Active Cooling of Turbine Components, Thermal Engineering Aspects in power Systems, R. S. Amano and B. Sunden, ed., WIT, Press Southampton, UK.

32. Simon, T. W., 2007, Chapters on: “Fundamental of Coolant Injection,” Discrete Hole Film Cooling Injection: Mixing Effects,” and “Effects of Mainstream Conditions,” Film Cooling Science and Technology for Gas Turbines: State-of-the-Art Experimental and Computational Knowledge, Lecture series 2007-06, R. S. Bunker and T. Arts, Editors, Von Karman Institute for Fluid Dynamics, Brussels Belgium.

33. Ibrahim, M., T. Simon, S. Mantell, D. Gedeon, G. Wood, K. Kelly, and J. McLean, 2007, "A Microfabricated Segmented-Involute-Foil Regenerator for Enhancing Reliability and Performance of Stirling Engines: Phase II Final Report for the Radioisotope Power Conversion Technology NRA Contract NAS3-03124 - Developing the Next Generation Stirling Engine Regenerator: Designing for Application of Microfabrication Techniques and for Enhanced Reliability and Performance in Space Applications, " NASA/CR-2007-215006 .

34. Tew, R., M. Ibrahim, D. Danila, T. Simon, S. Mantell, L. Sun, D. Gedeon, K. Kelly, J. McLean, G. Wood, and S. Qiu, 2007, "A Microfabricated Involute-Foil Regenerator for Stirling Engines," NASA-TM-2007-214973.

35. Simon, T., and Piggush, J., “Endwall Aerodynamics and Heat Transfer,” chapter of the book Turbine Aerodynamics, Heat Transfer, Materials and Mechanics- Progress in Astronautics and Aeronautics, Tom Shih and Vigor Yang, Editors, American Institute of Aeronautics &Aeronautics, September 2014.

36. Li, P. Y., Loth, E., Qin, C., Simon, T. W., and Van de Ven, “Open Accumulator Isothermal Compressed Air Energy Storage (CAES) System,” Chapter in Energy Storage Handbook, Stephen J. Bauer, ed., Wiley.


Presentation Only

1. Yue, Lindsey, Bader, Roman, Bayon Alicia, Hinkley, Simon, Terrence and Lipiński, Wojciech, 2017, “Experimental investigation of carbon dioxide capture and high-temperature thermal energy storage via metal oxide chemical looping in a 1 kW solar prototype reactor,” TFEC-IWHT2017, Las Vegas, NV.

2. Yue, L., Zapata, J., Ford, C., Kreider, P., Fayon, A., Hinkley, J., Simon, T., and Lipinski, W., 2017, Experimental investigation of carbon dioxide capture and high-temperature thermal energy storage via metal oxide chemical looping in a 1 kW solar prototype reactor, HT2017-5121